Skip to main content

この分解は修理ガイドでは ありません。 お持ちのAcer Liquid E1を修理する際は、iFixitの修理ガイドをご利用ください。

  1. Remove the plastic back and the exposed battery.
    • Remove the plastic back and the exposed battery.

    • Do not forget to remove sim- and SD-cards

    • Use a torx t5 to unscrew all screws. This will be the first and last time you'll use a screwdriver with this device.

  2. Use a plastic opening tool or spudger Pry around the side to release the backframe from the middleframe
    • Use a plastic opening tool or spudger

    • Pry around the side to release the backframe from the middleframe

    • Be careful as the frame is quite fragile

  3. To free the main board, remove the connector and antenna-cable Use a plastic spudger Be careful not to chip components
    • To free the main board, remove the connector and antenna-cable

    • Use a plastic spudger

    • Be careful not to chip components

  4. Tilting the main board will reveal this connection Use a plastic spudger to open the lock Carefully pull the flex cable out of it
    • Tilting the main board will reveal this connection

    • Use a plastic spudger to open the lock

    • Carefully pull the flex cable out of it

    • Don't put alot of stress on it

  5. MacBook Battery 修理キット

    最低価格 $69.99

    Buy Now

    MacBook Battery 修理キット

    最低価格 $69.99

    Buy Now
  6. At the bottom, use a pair of tweezers to remove the yellow tape from the connector Use a plastic spudger to unlock Pull the flexcable out carefully
    • At the bottom, use a pair of tweezers to remove the yellow tape from the connector

    • Use a plastic spudger to unlock

    • Pull the flexcable out carefully

  7. Next, use a platic spudger to remove the flex cable from its connection Next, use a platic spudger to remove the flex cable from its connection
    • Next, use a platic spudger to remove the flex cable from its connection

  8. Use a spudger to remove the bottom-plate from the frame. Be careful when using metal tools (like I did) Make sure the antenna cable isn't attached to anything except it's socket
    • Use a spudger to remove the bottom-plate from the frame.

    • Be careful when using metal tools (like I did)

    • Make sure the antenna cable isn't attached to anything except it's socket

  9. Let the remaining heat at 95°C for about 3-5 minutes to soften the adhesive Use an opening tool to pry at the top, between your digitizer and the middleframe Open it from the top, your digitizer-flex runs at the bottom
    • Let the remaining heat at 95°C for about 3-5 minutes to soften the adhesive

    • Use an opening tool to pry at the top, between your digitizer and the middleframe

    • Open it from the top, your digitizer-flex runs at the bottom

    • Be careful when using a heat-gun. Heat-guns don't distribute heat evenly and LCD-burns may occur

  10. To remove the LCD, remove the sticker on the back of the midframe. It conseals the LCD-flex Be careful when removing the sticker. It's glued tightly and too much stress will tear the LCD-flex Remove the LCD by pulling the whole cable through the midframe.
    • To remove the LCD, remove the sticker on the back of the midframe. It conseals the LCD-flex

    • Be careful when removing the sticker. It's glued tightly and too much stress will tear the LCD-flex

    • Remove the LCD by pulling the whole cable through the midframe.

  11. All done
    • All done

    • I hope you enjoyed it as much as I did

Maxim

メンバー登録日: 2014年04月30日

2,227 ポイント

3のガイドは作成済み

チーム

iFixers Belgium iFixers Belgium人のメンバー

Business

1 メンバー

3のガイドは作成済み

コメント1件

Great Manual.. it work fine! thanks,,

qwertykeyboard.404 - 返信

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 1

過去 30 日: 7

今までの合計 5,139