はじめに

Use this guide to replace the loudspeaker in your Huawei P10 smartphone. When reassembling your phone apply new adhesive where it is necessary.

パーツ

パーツは必要ありません。

Switch off your phone. Remove the two Pentalobe P2 screws at the bottom. Remove the SIM card tray.
  • Switch off your phone.

  • Remove the two Pentalobe P2 screws at the bottom.

  • Remove the SIM card tray.

コメントを追加する

Insert a plastic opening tool between the display and the case starting at the bottom area of your phone. Carefully pry the display with its parts out of the case. After you pried out the bottom end, use the opening tool to open the clamps on both sides.
  • Insert a plastic opening tool between the display and the case starting at the bottom area of your phone.

  • Carefully pry the display with its parts out of the case.

  • After you pried out the bottom end, use the opening tool to open the clamps on both sides.

コメントを追加する

Don't open the phone all the way, yet. The cable for the standby and volume buttons is still connected to the back cover. Swing open the phone backwards.
  • Don't open the phone all the way, yet. The cable for the standby and volume buttons is still connected to the back cover.

  • Swing open the phone backwards.

  • Use a spudger to disconnect the cable.

The cable is for the standby and volume buttons, not for the fingerprint sensor!

JaL - 返信

Thanks JaL, of course it is.

Tobias Isakeit -

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Remove the Phillips #00 screw. Use tweezers to remove the metal plate. Use a spudger to disconnect the battery flex cable.
  • Remove the Phillips #00 screw.

  • Use tweezers to remove the metal plate.

  • Use a spudger to disconnect the battery flex cable.

コメントを追加する

Remove the four Phillips #00 screws. Use Tweezers to remove the metal plate.
  • Remove the four Phillips #00 screws.

  • Use Tweezers to remove the metal plate.

コメントを追加する

Use a spudger to disconnect the main flex cable. Use tweezers to disconnect the antenna cable and pull it out of the clamp holding it down to the charging board.
  • Use a spudger to disconnect the main flex cable.

  • Use tweezers to disconnect the antenna cable and pull it out of the clamp holding it down to the charging board.

コメントを追加する

Use a spudger to disconnect the headphone jack and the loudspeaker flex cables. Use a spudger to disconnect the headphone jack and the loudspeaker flex cables.
  • Use a spudger to disconnect the headphone jack and the loudspeaker flex cables.

コメントを追加する

Do not damage any components sitting on the charging board while removing it. Use a spudger to pry out the charging board.
  • Do not damage any components sitting on the charging board while removing it.

  • Use a spudger to pry out the charging board.

  • Remove the charging board.

コメントを追加する

Only insert the spudger as deep as 1/16 of an inch to avoid damage. Use a spudger to carefully pry out the loudspeaker. There is some adhesive underneath so it might be a little bit sticky. You can  use an iOpener to loosen it.
  • Only insert the spudger as deep as 1/16 of an inch to avoid damage.

  • Use a spudger to carefully pry out the loudspeaker. There is some adhesive underneath so it might be a little bit sticky. You can use an iOpener to loosen it.

  • Remove the loudspeaker.

    • When reassembling your phone, apply new adhesive where it's necessary.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order. When reassembling your phone apply new adhesive where it is necessary.

Dominik Schnabelrauch

メンバー登録日: 2016年11月23日

12,950 ポイント

248のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

114 メンバー

5,916のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 10

過去 30 日: 42

今までの合計 230