メインコンテンツにスキップ

注意:あなたはさきほど閲覧しているガイドの前提となるページを編集しています。あなたが行った変更は、この手順を含むガイド全体に影響を与えます。

英語
日本語

手順 3を翻訳中

手順3
Steady the bracket from the left side using your fingers or tweezers. At the same time, insert a small (1 mm) flathead screwdriver under the tiny tab on the right. Finally, place one finger behind the tab, and pinch the bracket hard between your finger and the screwdriver to detach the cover.
  • Steady the bracket from the left side using your fingers or tweezers.

  • At the same time, insert a small (1 mm) flathead screwdriver under the tiny tab on the right.

  • Finally, place one finger behind the tab, and pinch the bracket hard between your finger and the screwdriver to detach the cover.

  • This releases two slotted tabs that hold the cover to the bracket, and should free the cover.

  • Prying the cover off can be challenging and may take more than one attempt. Be patient, and take care not to pull on the bracket or tear the attached cables.

ディスプレイとデジタイザーケーブル接続を含むブラケットは上部と下部のピースでできています。コネクターは下のブラケットに留められており、上部ブラケットは接続を外すには取り出す必要があります。

ブラケットの下半分を掴むため、先端が尖っているピンセットを使います。

上部メタル製ブラケットから下向きに突き出ている小さなメタル製タブがあります。

タブと下部のブラケットの間に小サイズのマイナスドライバー(1㎜)を差し込みます。隙間が広がるようにスクリュードライバーを左右に動かします。

この作業は、上部ブラケットを下のブラケットに留めている2つのタブを緩め、上部ブラケットから取り外すことができます。

[* icon_note] The bracket that contains the display and digitizer cable connections is made up of an upper and lower piece. The connectors are secured to the lower, and the upper must be removed to disconnect them.
[*
black] Use fine-tipped tweezers to graspSteady the lower half of the bracket.
[* icon_note] There is a small metal tab that protrudes downward
bracket from the upper metal bracketleft side using your fingers or tweezers.
[* black] InsertAt the same time, insert a small (1 mm) flathead screwdriver betweenunder the tiny tab on the right.
[* black] Finally, place one finger behind the tab,
and pinch the lower bracket,bracket ''hard'' between your finger and rotate the screwdriver to spreaddetach the gap.
[* black
cover.
[* icon_note
] This will releasereleases two slotted tabs that hold the upper bracketcover to the lowerbracket, and should free the upper bracketcover.
[* icon_caution] Prying the cover off can be challenging and may take more than one attempt. Be patient, and take care not to pull on the bracket or tear the attached cables
.
[* icon_note] The bracket that contains the display and digitizer cable connections is made up of an upper and lower piece. The connectors are secured to the lower, and the upper must be removed to disconnect them.
[*
black] Use fine-tipped tweezers to graspSteady the lower half of the bracket.
[* icon_note] There is a small metal tab that protrudes downward
bracket from the upper metal bracketleft side using your fingers or tweezers.
[* black] InsertAt the same time, insert a small (1 mm) flathead screwdriver betweenunder the tiny tab on the right.
[* black] Finally, place one finger behind the tab,
and pinch the lower bracket,bracket ''hard'' between your finger and rotate the screwdriver to spreaddetach the gap.
[* black
cover.
[* icon_note
] This will releasereleases two slotted tabs that hold the upper bracketcover to the lowerbracket, and should free the upper bracketcover.
[* icon_caution] Prying the cover off can be challenging and may take more than one attempt. Be patient, and take care not to pull on the bracket or tear the attached cables
.

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります