修理を始めるには

修理する権利

ストア

Canon PowerShot A80 Front Cover Replacement

作成者： Travis (そして 6 人のその他投稿者)
  • コメント: 2
  • お気に入り: 0

難易度

簡単

手順

11

所要時間

5分

セクション

2

フラグ

3

Inconsistent Images

一貫性のない画像

このガイドの画像を必要条件ガイドとより一致するように変更するとさらに素晴らしくなります。

Action Shots

アクションショット

アクションヒーローになりましょう！このガイドはある特定の動作をどのように行なうのか、より詳細な画像が必要です。

Confusing Text

テキストが不明瞭

このガイドのテキストの数カ所が混乱し、重複しトピックから外れています。編集してより明確にしてください！

はじめに

We will start with the camera intact and take off screws and other parts needed to remove the front cover of the camera

ツール

これらのツールを購入する

パーツ

パーツは指定されていません。

  1. Remove the three Phillips screws (shown) located at the bottom of the camera.

    • Remove the three Phillips screws (shown) located at the bottom of the camera.

    編集

  2. Open the door to the CompactFlash memory card slot by sliding it towards you and swinging it open. Remove the memory card if it is still in the camera.

    • Open the door to the CompactFlash memory card slot by sliding it towards you and swinging it open.

    • Remove the memory card if it is still in the camera.

    • Use the Phillips screwdriver to remove the Phillips screw (shown) underneath the memory card slot door.

    編集

  3. Remove the Phillips screw (shown) located inside the top of the memory card compartment.

    • Remove the Phillips screw (shown) located inside the top of the memory card compartment.

    編集

  4. Open the battery compartment door at the bottom of the camera by sliding the latch to the right and then sliding the door down. Remove the batteries from the compartment.

    • Open the battery compartment door at the bottom of the camera by sliding the latch to the right and then sliding the door down.

    • Remove the batteries from the compartment.

    • Unscrew the three Phillips screws (shown) located inside the battery compartment.

    • The screw on the left is longer than the other two.

    編集

  6. You should now able to remove the top lid of the camera.

    • You should now able to remove the top lid of the camera.

    • Be cautious of the fragile mylar cable that connects the lid to the main body of the camera.

    • Removing the lid takes a little force. Do this gently. There may be a snapping sound.

    • The door to the memory card compartment will be freed and should be removable now.

    • In other versions of this camera, there is a tab that secures the top from the wrist strap. If yours has this, you won't be able to completely separate the top until you have removed the top screw in Step 8.

    編集

  7. Remove the lower Phillips screw (shown) from the side of the camera.

    • Remove the lower Phillips screw (shown) from the side of the camera.

    • Open the small rubber door below this screw that covers the connectors.

    編集

  8. Open and pivot the LCD screen to its widest open position. Remove the rear cover by pulling it straight away from the body of the camera.

    • Open and pivot the LCD screen to its widest open position.

    • Remove the rear cover by pulling it straight away from the body of the camera.

    • When reassembling the camera, remember to replace the screws in the same location from which you removed them. Otherwise, you may damage the camera.

    編集

  9. Now remove the top screw 3.3 mm long on the side of the camera that hold the side panels and the front cover using the #00 screwdriver. Gently remove the side panel of the camera by pulling it away form the camera.

    • Now remove the top screw 3.3 mm long on the side of the camera that hold the side panels and the front cover using the #00 screwdriver.

    • Gently remove the side panel of the camera by pulling it away form the camera.

    • The side panel may get stuck on the internal wires, so gently wiggle this panel loose.

    編集

  10. Unscrew the 2.4 mm long screw that holds on the front panel underneath the side panel using the #00 screwdriver.

    • Unscrew the 2.4 mm long screw that holds on the front panel underneath the side panel using the #00 screwdriver.

    編集

  11. Underneath the battery cover there is another 3.8 mm screw in the corner that needs to be removed using the #00 screwdriver.

    • Underneath the battery cover there is another 3.8 mm screw in the corner that needs to be removed using the #00 screwdriver.

    編集

  12. Gently pull up on the front cover to remove it from the body

    • Gently pull up on the front cover to remove it from the body

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

6他の投稿者と一緒に

Travis

メンバー登録日: 2011年01月28日

214 ポイント

1ガイドが承認済み

バッジ: 8

+5 個以上のバッジ

チーム

Cal Poly, Team 7-31, Regan Winter 2011 Cal Poly, Team 7-31, Regan Winter 2011人のメンバー

CPSU-REGAN-W11S7G31

6 メンバー

12のガイドは作成済み

0 件のコメント

コメントを追加

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 22

今までの合計 3,835