Skip to main content

注意:あなたは必要条件ガイドを編集しています。あなたが行なう変更は、この手順を含む全ての14個のガイドに反映されます。

英語
日本語

手順 8を翻訳中

Step 8
To install a new back cover:
  • To install a new back cover:

  • Use tweezers to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive.

  • Peel the adhesive backing off of the new rear glass, carefully line up one edge of the glass against the phone chassis, and firmly press the glass onto the phone.

  • Follow this guide to reinstall the old back cover, or to install a back cover without pre-installed adhesive.

  • Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.

  • If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

  • You may also need to transfer the camera bezel to your new part. If that's the case, follow our camera bezel replacement guide.

リアガラスを交換する前に、古い圧着剤をデバイス本体から剥がしてください。

古い圧着剤を剥がした後、高濃度のイソプロピルアルコール(濃度90%以上)で本体の端を綺麗に拭き取ってから、新しい圧着剤を装着してください。

[* icon_reminder] Before replacing your rear glass you will needTo install a new back cover:
[* black] Use tweezers
to remove the oldpeel away any remaining adhesive from the phone body.
[* black] After removing the old adhesive,
phone's chassis. Then clean the edges of the phone bodyadhesion areas with high concentration isopropyl alcohol (at least 90%), then apply90%) and a lint-free cloth to prep the surface for the new adhesive.
[* black] Peel the adhesive backing off of the new rear glass, carefully line up one edge of the glass against the phone chassis, and firmly press the glass onto the phone.
[* icon_reminder] [guide|124003|Follow this guide|new_window=true] to reinstall the old back cover, or to install a back cover without pre-installed adhesive.
[* icon_note] Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.
[* icon_note] If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.
[* icon_reminder] You may also need to transfer the camera bezel to your new part. If that's the case, follow our [guide|122484|camera bezel replacement guide|stepid=236006|new_window=true].
[* icon_reminder] Before replacing your rear glass you will needTo install a new back cover:
[* black] Use tweezers
to remove the oldpeel away any remaining adhesive from the phone body.
[* black] After removing the old adhesive,
phone's chassis. Then clean the edges of the phone bodyadhesion areas with high concentration isopropyl alcohol (at least 90%), then apply90%) and a lint-free cloth to prep the surface for the new adhesive.
[* black] Peel the adhesive backing off of the new rear glass, carefully line up one edge of the glass against the phone chassis, and firmly press the glass onto the phone.
[* icon_reminder] [guide|124003|Follow this guide|new_window=true] to reinstall the old back cover, or to install a back cover without pre-installed adhesive.
[* icon_note] Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.
[* icon_note] If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.
[* icon_reminder] You may also need to transfer the camera bezel to your new part. If that's the case, follow our [guide|122484|camera bezel replacement guide|stepid=236006|new_window=true].

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります