修理を始めるには コミュニティ ストア
リペアコミュニティに参加 - アカウントの作成

Razer DeathAdder V3 Pro Encoder Replacement

はじめに

If your Razer DeathAdder V3 Pro's Scroll Wheel is unresponsive to input, jumping, or responds incorrectly, you may need to replace the Scroll Wheel Encoder.

For any quick fixes, please visit our troubleshooting guides for the Razer DeathAdder V3 Pro Scroll Wheel Not Responding to Input and Razer DeathAdder V3 Pro Spotty Wired Connection. If these fixes do not resolve your issues, please follow this guide to replace your scroll wheel.

Before you begin the replacement, please make sure that you have unplugged and powered off the device.

必要な工具と部品

  1. Razer DeathAdder V3 Pro Encoder Replacement, Scroll Wheel: 手順 1、 3の画像 1 Razer DeathAdder V3 Pro Encoder Replacement, Scroll Wheel: 手順 1、 3の画像 2 Razer DeathAdder V3 Pro Encoder Replacement, Scroll Wheel: 手順 1、 3の画像 3

    • Use a pry tool or fingernail to carefully remove the large foot on the lower end of the mouse.

    • Remove the three 7 mm screws using a Torx T6 screwdriver.

    翻訳

  2. Razer DeathAdder V3 Pro Encoder Replacement: 手順 2、 2の画像 1 Razer DeathAdder V3 Pro Encoder Replacement: 手順 2、 2の画像 2

    • BEFORE YOU OPEN THE MOUSE: Be careful at this point. Both shells are connected with a cable in the front of the mouse.

    • Insert a spudger into the seam between the top and bottom shells.

    • Gently work around the edges unclipping the internal latches.

    • Slowly lift the top shell but do not remove it yet; the cables are still attached to the circuit board.

    • Carefully pull the shells apart to unplug the cable in the front.

    翻訳

  3. Razer DeathAdder V3 Pro Encoder Replacement: 手順 3、 2の画像 1 Razer DeathAdder V3 Pro Encoder Replacement: 手順 3、 2の画像 2

    • Using a small pry tool or your fingers, gently pop the scroll wheel up and out of its housing

    翻訳

  5. Razer DeathAdder V3 Pro Encoder Replacement, Encoder: 手順 4、 1の画像 1

    • Use a T6 Torx screwdriver to remove the 5mm screws securing the circuit board.

    • Unplug the battery from its connection on the right side.

    • Be careful not to break the two clips that hold the PCB at the front of the mouse.

    翻訳

  6. Razer DeathAdder V3 Pro Encoder Replacement: 手順 5、 1の画像 1

    • At the front of the PCB next to the encoder, remove the switch held in place by clips by gently pulling it free.

    翻訳

  7. Razer DeathAdder V3 Pro Encoder Replacement: 手順 6、 2の画像 1 Razer DeathAdder V3 Pro Encoder Replacement: 手順 6、 2の画像 2

    • Wear eye protection.

    • Take care not to damage the PCB or any other components.

    • Use a pair of flush cutters to cut the legs of the encoder.

    • Desolder the legs of the 15 mm encoder on the underside of the PCB.

    • Remove the encoder.

    • Always solder in a well ventilated area.

    • Use a solder sucker to remove any excess solder.

    翻訳

  8. Razer DeathAdder V3 Pro Encoder Replacement: 手順 7、 1の画像 1

    • Press the new 15 mm encoder into place

    • If the encoder does not fit properly, clean the old solder more thoroughly.

    • Solder the new 15 mm encoder into place.

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

3人の作成者と共同で作成されました。

Nicholas

メンバー登録日: 09/24/25

453 ポイント

4のガイドは作成済み

バッジ: 6

+3 個以上のバッジ

チーム

Texas Tech, Team 2-5, Johansen Fall 2025 Texas Tech, Team 2-5, Johansen Fall 2025人のメンバー

TTU-JOHANSEN-F25S2G5

5 メンバー

5のガイドは作成済み

0件のガイドコメント

コメントを追加

統計データ:

過去 24時間: 5

過去 7 日: 28

過去 30 日: 142

今までの合計 287