修理を始めるには コミュニティ ストア

Samsung Galaxy S8 玻璃背板组件更换

注意：あなたは必要条件ガイドを編集しています。あなたが行なう変更は、この手順を含む全ての15個のガイドに反映されます。

ガイドに戻る
英語
中国語
前の手順

手順 8を翻訳中

手順8
Samsung Galaxy S8 Back Glass Assembly Replacement: 手順 0、 1の画像 1

  • To install a new back cover:

  • Use tweezers to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive.

  • Peel the adhesive backing off of the new rear glass, carefully line up one edge of the glass against the phone chassis, and firmly press the glass onto the phone.

  • Follow this guide to reinstall the old back cover, or to install a back cover without pre-installed adhesive.

  • Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.

  • If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

  • You may also need to transfer the camera bezel to your new part. If that's the case, follow our camera bezel replacement guide.

要安装新的后盖：

使用镊子从手机底盘上剥离所有剩余的粘合剂。 然后用高浓度异丙醇（至少 90%）和无绒布清洁粘合区域，以便让新的粘合剂发挥最佳性能。

撕下新后玻璃上的背胶，小心地将玻璃的一侧与手机底盘对齐，然后将玻璃牢牢地压在手机上。

按照本指南重新安装旧后盖，或安装没有涂粘合剂的后盖。

在涂上新的粘合剂和重新密封手机之前，请务必将手机开机并测试维修是否成功。

如果需要，你可以重新安装后盖而无需更换粘合剂。 去除任何可能影响后盖安装的大块粘合剂。 安装后，加热后盖并施加压力以将其固定。 它并不防水，但胶水通常足够坚固以固定住。

您可能还需要将相机挡板转移到新部件上。 如果是这种情况，请按照我们的相机挡板更换指南进行操作。

[* icon_reminder] To install a new back cover:
- [* black] Use tweezers to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive.
+ [* black] Use [product|IF145-020|tweezers] to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive.
[* black] Peel the adhesive backing off of the new rear glass, carefully line up one edge of the glass against the phone chassis, and firmly press the glass onto the phone.
[* icon_reminder] [guide|124003|Follow this guide|new_window=true] to reinstall the old back cover, or to install a back cover without pre-installed adhesive.
[* icon_note] Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.
[* icon_note] If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.
[* icon_reminder] You may also need to transfer the camera bezel to your new part. If that's the case, follow our [guide|122484|camera bezel replacement guide|stepid=236006|new_window=true].

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります。