はじめに

Replacing the speaker requires soldering and extensive disassembly. Refer to iFixit's soldering guide if you have never used a soldering iron or if you need a refresher.

On the back of the phone, place your thumb on the three raised bumps and slide the back cover upward. On the back of the phone, place your thumb on the three raised bumps and slide the back cover upward.
  • On the back of the phone, place your thumb on the three raised bumps and slide the back cover upward.

コメントを追加する

Lift and remove the battery.
  • Lift and remove the battery.

コメントを追加する

Remove the two screw covers at the top of phone with tweezers. Remove the two screw covers at the top of phone with tweezers.
  • Remove the two screw covers at the top of phone with tweezers.

コメントを追加する

Remove the six Phillips #000 (3mm) screws.
  • Remove the six Phillips #000 (3mm) screws.

コメントを追加する

Use the plastic opening tool to pry the back cover off. Insert the tool between the back cover and red mid section and go around the entire phone. The plastic side buttons fall out when you take the back cover off. The back cover is connected to the speaker by red and black wires.
  • Use the plastic opening tool to pry the back cover off. Insert the tool between the back cover and red mid section and go around the entire phone.

  • The plastic side buttons fall out when you take the back cover off.

  • The back cover is connected to the speaker by red and black wires.

コメントを追加する

Use the tweezers to remove the red and black wires connecting the speaker to the green motherboard by pinching the sides of the plastic base near the motherboard.
  • Use the tweezers to remove the red and black wires connecting the speaker to the green motherboard by pinching the sides of the plastic base near the motherboard.

  • Set the back cover with the speaker aside.

コメントを追加する

Use the plastic opening tool to gently lift the snapped-in motherboard from the front panel. An orange ribbon from the LCD is connected to the underside of the motherboard, so do not force the motherboard from the rest of the phone yet.
  • Use the plastic opening tool to gently lift the snapped-in motherboard from the front panel.

  • An orange ribbon from the LCD is connected to the underside of the motherboard, so do not force the motherboard from the rest of the phone yet.

コメントを追加する

Gently remove the blue transparent tape from the connector.
  • Gently remove the blue transparent tape from the connector.

コメントを追加する

With the plastic opening tool, gently pry the LCD connector from the motherboard.
  • With the plastic opening tool, gently pry the LCD connector from the motherboard.

  • Set the motherboard aside.

コメントを追加する

Take the front case and unscrew the four Phillips #000 (1mm) screws around the ribbon.
  • Take the front case and unscrew the four Phillips #000 (1mm) screws around the ribbon.

コメントを追加する

Gently pull the orange ribbon from the number pad casing.
  • Gently pull the orange ribbon from the number pad casing.

  • Set the number pad case to the side once it is detached from the ribbon.

コメントを追加する

Remove the two red sticker screw coverings at the top corners with tweezers.
  • Remove the two red sticker screw coverings at the top corners with tweezers.

コメントを追加する

Unscrew the four Phillips #000 (3mm) screws at the corners of the phone.
  • Unscrew the four Phillips #000 (3mm) screws at the corners of the phone.

コメントを追加する

Pry the red sliding backing from the front cover by inserting the plastic opening tool in between the two sections and going around the entire phone. Set the red sliding backing and front cover to the side.
  • Pry the red sliding backing from the front cover by inserting the plastic opening tool in between the two sections and going around the entire phone.

  • Set the red sliding backing and front cover to the side.

コメントを追加する

Be very careful to not damage the keypad board when using the plastic opening tool.
  • Be very careful to not damage the keypad board when using the plastic opening tool.

  • Gently pry the LCD ribbon from the left side of the front cover using the plastic opening tool.

  • One LCD ribbon is still connected to the keyboard, so do not attempt to remove it from the front cover.

コメントを追加する

Use the plastic opening tool to partially lift up the keyboard from the front of the phone. Slowly rotate the keyboard clockwise while pulling it to the right to disconnect the second LCD ribbon from the keyboard.
  • Use the plastic opening tool to partially lift up the keyboard from the front of the phone.

  • Slowly rotate the keyboard clockwise while pulling it to the right to disconnect the second LCD ribbon from the keyboard.

  • Remove the keyboard from the phone and set aside.

コメントを追加する

Do not attempt to completely remove the speaker from the phone at this point - it is still connected to the LCD screen.
  • Do not attempt to completely remove the speaker from the phone at this point - it is still connected to the LCD screen.

  • Use the plastic opening tool to pry the front speaker from the phone.

コメントを追加する

Use a soldering iron to desolder the lead junctions. If you have never used a soldering iron or you need a refresher, check out iFixit's soldering guide. Separate the speaker from the LCD screen.
  • Use a soldering iron to desolder the lead junctions. If you have never used a soldering iron or you need a refresher, check out iFixit's soldering guide.

  • Separate the speaker from the LCD screen.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

Annie White

メンバー登録日: 2013年10月18日

262 ポイント

4のガイドは作成済み

チーム

Cal Poly, Team 4-27, Amido Fall 2013 Cal Poly, Team 4-27, Amido Fall 2013人のメンバー

CPSU-AMIDO-F13S4G27

4 メンバー

16のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 1

今までの合計 245