修理を始めるには コミュニティ ストア

2009年6月発売/ 2.53 GHz Core 2 デュオプロセッサ

170回答 すべてを表示

オプション

Top side corner of MBP screen lifting up, needs glue maybe? (Photo)

Block Image

Hello all. My old 2009 MBP has the back corner screen top lifting up when I close the machine. The screen works fine, and I can push the screen back down in the corner. I assume the glue needs to be re-applied?

I took the machine to a local repair shop, and they wanted to replace the entire top half of the machine, including the LCD screen, which I really can’t afford, and I’m not sure it needs to be replaced. Otherwise the machine is still going strong after almost 10 years.

If anyone has dealt with a similar issue, please let me know.

回答がありました！ 回答を表示 同じ問題があります

この質問は役に立ちましたか？

はい いいえ
スコア 0
コメントを追加

2件の回答

フィルタ：
参考になった順 新しい順 古い順
ベストアンサー

オプション

Take a look at this video and see if it helps, you may just need to tighten hinges and that may be enough but it looks like the metal blocks for hinge reinforcement have separated from the top chassis and may need to be reglued with epoxy.

https://www.youtube.com/watch?v=Gi6vlshg...

このアンサーは役に立ちましたか？

はい いいえ
スコア 5

4 件のコメント:

That is super helpful, thank you Ben. I'll update when I can get home and try this.

さんによる

I'm with @benjamen50 here! Epoxy is the ticket! But you'll need to get the display apart to clean the old glue and you'll want to scuff up the surface to make a better surface for the epoxy to adhere to.

Here's the IFIXIT guide to take your display fully off: MacBook Pro 15" Unibody 2.53 GHz Mid 2009ディスプレイアセンブリの交換 and here's the IFIXIT guide to take the display assembly apart MacBook Pro 15" Unibody Late 2008/Early 2009 LCDの交換 Jump down to Step14 and pick it up there.

Once the display is out you can clean and sand the pulled areas. You'll want to place a display frame & cover on a good flat surface with a wood board going on top with a bit of weight for a good 24hrs for the epoxy to cure. I would also place added epoxy around the frame at the glue points to add more strength. Just make sure you don't go into the areas the display fits into. And don't forget to sand the surfaces to give the epoxy a better grip!

さんによる

Thank you so much for the extra info and links Dan. I think you're correct also. After looking inside, I don't think it's the hinge, but the display coming apart.

さんによる

I have this issue too can anyone recommend me a good brand for epoxy ?

さんによる

コメントを追加

オプション

Chances are its from apples terrible design of having ALL the hot air from the cpu and gpu blowing on the hinge glue. Not your fault. Put some new epoxy and it should be fine

このアンサーは役に立ちましたか？

はい いいえ
スコア 1

2 件のコメント:

Thank you Ethan, I think you're right that the hot hair has had an impact over the years.

さんによる

For sure. Good luck

さんによる

コメントを追加

回答を追加する

nicholas.he さん、ありがとうございました！
統計データ:

過去 24時間: 1

過去 7 日: 9

過去 30 日: 12

今までの合計 558