メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

2012年9月12日に発表されたApple社による6番目となる iPhone。このデバイスの修理方法は前モデルと類似しており、スクリュードライバーと開封工具が必要です。GSMかCDMA方式、16/32/64 GB。 本体色は黒と白。

3396の回答 すべてを表示

How to remove white marks from iPhone 5 screen?

Hello. I did it to myself because the power button was not responding well it figured out that dirt might be the problem so i decided to spray just a little bit of sonax electronic component cleaner.

After i turned the phone on like half a hour latter i was left with these white water marks on the phone.

At first the marks where bigger but became to fade like in the photo. Tried putting it on rice and everything so today i decided to open the lcd digitizer and after i removed the back cover i saw the marks of the Digitizer film.

They seem very hard to clean and i am afraid to use any products like alcohol or anything else.

Also my camera now its not focusin on macro :///

Please anyone, is there anyway to clean the Digitizer or do i have to buy a new lcd ?

Thankss

Block Image

Block Image

Block Image

この質問に回答する 同じ問題があります

この質問は役に立ちましたか?

スコア 1

コメント:

i have same problem .. any solution ???

さんによる

same problem then backlight kept falling

さんによる

コメントを追加

Manta Driver Kit

どんな修理にでも対応可能な112ビット

Upgrade Your Toolbox

Manta Driver Kit

Upgrade Your Toolbox

8件の回答

最も参考になった回答

I think that you could try putting a new layer of the film on the unit. The film causes the backlight to diffuse evenly and the damage to it is what is causing the brighter spots on the screen. I would start with buying a broken screen assembly with the film intact and attempt to move it over to the one on your device.

この回答は役に立ちましたか?

スコア 1

コメント:

But is the film replaceable. I mean can i easy remove it does it have any adhesives or how can i do it. Thankss :)

さんによる

did you solved this issue?

さんによる

コメントを追加

The problem is the liquid is under that black film and it causing the white spots

この回答は役に立ちましたか?

スコア 1

コメント:

Only solution is to remove the rear film and clean the damage but you risk breaking the lcd

さんによる

Can this spread?! I dropped my phone in water and after putting it in rice it works I'm just worried about whether or not this white will spread through my whole screen

さんによる

コメントを追加

Put it face up on a warm surface. Note that it may take a few days depending on the size of the marks.

この回答は役に立ちましたか?

スコア 1

コメント:

This actually may work i put it in for about 5 minutes and it faded a little bit

さんによる

コメントを追加

If you attempt to clean it be sure to use 99% alcohol so it all evaporates. I had the same issue on a 4 and this took care of it. but im not sure if the alcohol will mess with the film on the 5.

この回答は役に立ちましたか?

スコア 0

コメント:

I tried with 96 % Alcohol on the top right angle just a bit but it seems to leave a mark so i didnt go further :/

さんによる

コメントを追加

Any solution

この回答は役に立ちましたか?

スコア 0
コメントを追加

What you need is a new backlight (if you have solder handy)

Backlight is very easy to remove. it's only held by sticky tape around the edges.

You need to remove the tape that covers the connection to the LCD.

Use a solder to detach the backlight.

then reverse the process to attach the new one.

Dont forget to clean the back of the LCD before you put on the new backlight.

otherwise you need a new LCD assembly.

Nice and easy job ..

plus you need a new rear camera ..

basically the liquid you used had sipped through the gap on power button.

underneath that power button, is the rear camera and the LCD.

it sounds like your rear camera is now liquid damaged.

この回答は役に立ちましたか?

スコア 0
コメントを追加

Lol It cum XD LMAO!!111!!!11!1!

この回答は役に立ちましたか?

スコア 0
コメントを追加

it seems that solution managed to slip inside the reflector of lcd assembly and after evaporating srain marks is there in reflector and this is causing uneven reflection of backlight of lcd on display and this white spot is appearing so i suggest remove display assembly completely and submerge display assembly in 99% isopropyl cleaning solution and move display assembly back and fourth it will flush out the dried strain marks and cleanup the reflector without harming lcd display and after few minutes or 1hour max into the exposure of heat isopropyl solution will evaporates and display will work fine and marks should be gone .

この回答は役に立ちましたか?

スコア 0
コメントを追加

回答を追加する

Blendi さん、ありがとうございました!
統計データを表示:

過去 24時間: 0

過去 7 日: 18

過去 30 日: 70

今までの合計 61,795