Schwarzstein

Ah, yes, solenoid is the word for "electric magnet", thank you. Look at that video, it shows a damaged brewgroup, but you can see the action of the valve: https://www.youtube.com/watch?v=Pxad75B2... At 0,18 the solenoid gets current and opens the valve by pushing the metal axle. For that duration a humming noise is hearable, listen good. At 0,23 the noise ends in the moment the valve snaps back. If you hear fot those 5 seconds a knocking sound it is very shure that there is a problem with that solenoid, the valve or electronics. I hope you understand me, sorry. :)

Hello, that sound is from the electric-magnet at the drainage-valve. When the brewing stops, the fluidsystem would rinse through the nozzle in the front and it would give many drops of coffee. So this problem is solved by the drainage-valve, which lets the water out and air in to stop the tripping. The electric magnet knocks a steel-needle at a plastic cap which is mounted to a metal axle in the valve which then opens. Sometimes these Juras make awful humming noises while the electric-magnet has current, too. - when these Juras get older. As long as the knock sound and the humming is only hearable while the drainage-valve has opened evverything is okay. :) Friendly greets and good luck. :)

If you take R type Batterie you have to change often. If you take LR type Batterie it works at normnal usage about 1 year !! The phone has a Energy-saving. If the child does not touch it for about a minute the phone goes in stand-by mode and so the batteries stay fresh. I like it.

No it is not perfectly waterproof, you can not take it in water. but a little rain wont damage it. My child poured milk above it, that was no problem, cleaned it, works with no problems.

This toy is durable. But it is bad soldered. We have it 2 years. My child often let it fall down. One cable of the powerswitch broke, i had to solder it new. It is good quality, the voice and sounds are clear and the touchscreen really works with twelve fields. It is a good toy, my child likes it a lot - when my child has a bad time that babyphone will make him smile again. Nice.

Hello, when there is NO Drainagevalve the water can not go through the brewgroup. The hose which goes into the Drainagevalve is also the one who brings the fresh, clear hot water from the valve near the heatingelement. When teh Drainagevalve is closed, the water goes through the brewgroup and makes the coffee. For a dry waste, the drainagevalve opens after the brewing and lets the water flow out and air in, so the wate gets out easy and isnt very wet. the drainagevalve is switched by an electric magnet, it mmakes a loud click noise. Jura Capresso IMPRESSA J5 Drainage Valve disassembly in this link: the hose brings fresh hot clean water, in picture ONE the part in the white circle lets the water into the brewgroup dock. The side where you can see the spring is the middlewall, behind that wall is the elctric magnet. sorry for my bad english, was not best at school. XD

Bonjour, ce type de visse s'appelle "E Torx" Il y a un kit professionel de Proxxon, Proxxon Nr 23102. https://www.google.de/search?q=Proxxon+N...-tzapqL8xwIVSpwaCh0rXgjN&biw=807&bih=559 Bonne chance.

I've made a new Photo-story for you, specially about the top piston and its seals (o-rings.) You'll find it in the "Maintenance guides" For Saeco INCANTO SBS. Enjoy and good luck.

Look in the guide, step # 9. There, on the second picture, you see that long, black part on top of the piston. This part can be turned: it mounts the strainer of the top-piston. when you turn it, the screw of the strainer should counterrotate. When the strainerscrew leaves that part, just pull out that black piece; there you will find a black O-ring. That O-ring often leaks after reparation because the strainer-screw is often mounted too tight. For more information, google "Rändelspannmutter Saeco". There is a new version and an older one, look carefully. Good luck !

Well, my child played with that Vacuum-cleaner and it overheated.

So I had to do this repairmanual for you.

Do not let play children with Machines. ;)

Good work.

I have done it the same way,

the wire at the switch was bad soldered,

but it was easy to repair it and i soldered it new.

Nice.

Good work !

Nice.

I did not see the black line in mine,

i opened the foil and glued it new together . Not so nice. :D

But it works.

Great ! :) Thank you.

Ja, okay, i made some pictures for you. The optics are in Step 10.

Enjoy.

Freundliche Grüsse. :)

Hello,

the hose from outside has 1/4 inch diameter, that's 6,35 mm. Right. :)

But inside, where the original bottle-filter is connected, the inlet hose has 5/16 inch (ca 8 mm) and the outlet hose has 1/4 inch.

In STEP 6 picture 2 is shown the different diameters. The second grey coupler is thicker, thats an adapter from 1/4 inch to 5/16 inch. I've made a new picture for you in STEP 7.

Friendly greets. :)