メインコンテンツにスキップ

iPhone 4のバッテリーの交換

注意:あなたはさきほど閲覧しているガイドの前提となるページを編集しています。あなたが行った変更は、この手順を含むガイド全体に影響を与えます。

英語
日本語

手順 3を翻訳中

手順3
iPhone 4 Battery Replacement: 手順 0、 3の画像 1 iPhone 4 Battery Replacement: 手順 0、 3の画像 2 iPhone 4 Battery Replacement: 手順 0、 3の画像 3
  • Use the clear plastic pull tab to gently lift the battery out of the iPhone.

  • If the tab breaks before the battery is freed, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery. Wait about one minute for the alcohol solution to weaken the adhesive. Carefully slide a spudger under the battery tab to release the adhesive.

  • Prying in other places may cause damage. Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.

  • If there's any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.

  • If your replacement battery came in a plastic sleeve, remove it before installation by pulling it away from the the ribbon cable.

  • Before reconnecting the battery connector, be sure the contact clip (shown in red) is properly positioned next to the battery connector.

  • Before reassembly, clean metal-to-metal contact points with a de-greaser such as windex. The oils from your fingers have the potential to cause wireless interference issues.

  • Perform a hard reset after reassembly. This can prevent several issues and simplify troubleshooting.

透明のプラスチック製プルタブを使って丁寧にiPhoneからバッテリーを引っ張ります。

バッテリーが外れる前にタブが切断した場合は、バッテリー端に90%以上の高濃度イソプロピルアルコールを数滴垂らしてください。アルコール溶液が接着力を弱めるまで、約1分待ちます。バッテリータブの下にスパッジャーを慎重に滑り込ませ、接着剤を剥がしします。

他の場所をこじ開けると破損することがあります。バッテリーを無理に引き抜こうとしないでください。必要に応じて、さらに数滴のアルコールを垂らし、接着力を弱めます。オープニングツールでバッテリーを変形させたり、穴を開けたりしないでください。

デバイス内部にアルコール溶液が残っている場合は、丁寧に拭き取るか、自然乾燥させてから新しいバッテリーを装着してください。

交換するバッテリーがプラスチック製スリーブに入っている場合、取り付ける前にリボンケーブルから引き抜いて外します。

バッテリーコネクターを再接続する前に、コンタクトクリップ(赤でマークされています)がバッテリーコネクターの隣の正しい位置に装着されているか確認してください。

再組み立ての前に、メタル接合ポイントをwindex(窓拭き用クリーナー)などで綺麗に拭き取ってください。油脂がワイヤレス通信の妨害となることがあります。

再組み立ての後はハードリセットを行ってください。これはトラブルシューティングを簡単にして、幾つかの問題を防いでくれます。

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります