メインコンテンツにスキップ

注意:あなたは必要条件ガイドを編集しています。あなたが行なう変更は、この手順を含む全ての2個のガイドに反映されます。

英語
日本語

手順 1を翻訳中

手順1
Starting 15mm below the right page-turning button, insert the middle of the pry tool. Pry open the back of the device using the pry tool, or similar plastic opening tool. The flexi cable for the screen is 10mm wide and passes 10mm to 20mm below the right page turn and is very easy to tear the edge. Do not attempt to pry directly on the page turning buttons. This will damage the buttons.  By inserting it at 15mm this will reduce the chance of damaging the flexi cable. Look closely at the image of Kindle with the back removed, this will help to identify the location. If you are having trouble getting an initial gap to pry from, run the flat edge of the pry tool along the front-to-back plate seam until it slips into a gap.
  • Starting 15mm below the right page-turning button, insert the middle of the pry tool. Pry open the back of the device using the pry tool, or similar plastic opening tool. The flexi cable for the screen is 10mm wide and passes 10mm to 20mm below the right page turn and is very easy to tear the edge.

  • Do not attempt to pry directly on the page turning buttons. This will damage the buttons. By inserting it at 15mm this will reduce the chance of damaging the flexi cable. Look closely at the image of Kindle with the back removed, this will help to identify the location.

  • If you are having trouble getting an initial gap to pry from, run the flat edge of the pry tool along the front-to-back plate seam until it slips into a gap.

  • Don't insert your tool too far, or you may damage some of the orange flex cables near the edges of the device.

  • When reinstalling the back cover, slide the bottom edge into place first, and then press up the sides and along the top until all the clips snap into place.

いずれかのページめくりボタンの真上から始めて、てこのツールまたは同様のプラスチック製の開封ツールを使用して、デバイスの背面をてこのように開けます。

ページめくりボタンを直接こじ開けようとしないでください。 ボタンが破損します。

最初の隙間をこじ開けるのに問題がある場合は、こじり具の平らな端を前から後ろのプレートの継ぎ目に沿って、隙間に滑り込むまで動かします。

ツールを奥深くまで差し込まないでください。デバイス端に搭載されているオレンジのフレックスケーブルを破損してしまうことがあります。

バックカバーを再装着する際は、まず下部の端をスライドしてからサイドから上部に向けてクリップを装着します。

-[* black] Starting just above one of the page-turning buttons, pry open the back of the device using a pry tool, or similar plastic opening tool.
-[* icon_caution] Do not attempt to pry directly on the page turning buttons. This will damage the buttons.
+[* black] Starting 15mm below the right page-turning button, insert the middle of the pry tool. Pry open the back of the device using the pry tool, or similar plastic opening tool. The flexi cable for the screen is 10mm wide and passes 10mm to 20mm below the right page turn and is very easy to tear the edge.
+[* icon_caution] Do not attempt to pry directly on the page turning buttons. This will damage the buttons. By inserting it at 15mm this will reduce the chance of damaging the flexi cable. Look closely at the image of Kindle with the back removed, this will help to identify the location.
[* icon_note] If you are having trouble getting an initial gap to pry from, run the flat edge of the pry tool along the front-to-back plate seam until it slips into a gap.
[* icon_caution] Don't insert your tool too far, or you may damage some of the orange flex cables near the edges of the device.
[* icon_reminder] When reinstalling the back cover, slide the bottom edge into place first, and then press up the sides and along the top until all the clips snap into place.

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります