修理を始めるには コミュニティ ストア

Kindle 3 バッテリーの交換

注意：あなたはさきほど閲覧しているガイドの前提となるページを編集しています。あなたが行った変更は、この手順を含むガイド全体に影響を与えます。

ガイドに戻る
英語
日本語
次の手順

手順 1を翻訳中

手順1
Kindle 3 Battery Replacement, Remove Rear Cover: 手順 0、 3の画像 1 Kindle 3 Battery Replacement, Remove Rear Cover: 手順 0、 3の画像 2 Kindle 3 Battery Replacement, Remove Rear Cover: 手順 0、 3の画像 3
Remove Rear Cover

  • Turn the device upside-down and insert a pry tool between the two case pieces.

  • On the left side just below the buttons there's a delicate ribbon cable that's part of the screen assembly and may be severed by a pry tool. (This is shown in the third photo, it's where the tool is pointing.) Regardless of where you start, stay clear of this area!

  • If you are having trouble getting an initial gap to pry from, run the flat edge of the pry tool along the front-to-back plate seam until it slips into a gap. You can also flex the device slightly and work a tool into one of the lower corners, which have a lot of empty space behind them rather than fragile components.

  • Looking at the back face, another safe place to start is on the right side just below the page turn buttons. (Note the green arrow in the board photo, which is rotated 90 degrees counter-clockwise.) The tool goes between the lower button and the hinge cover slot. If there isn't a slot there, you're on the wrong side!

  • Do not attempt to pry directly on the page turning buttons.

  • Work the pry tool around the edge of the case, releasing the 18 clips. Don't insert your tool too far, or you may damage components near the edges of the device. The clips are all in the outer edge of the backplate anyway. Note that the clip above the power switch is bigger and stronger than the rest.

  • Pull the rear cover off. The remaining two clips near the center of the back are surprisingly strong, but they face in the same direction so don't just pull up. Instead slide the cover slightly towards the top of device to release them.

  • When reinstalling the back cover, slide the bottom edge into place first, and then press up the sides and along the top until all the clips snap into place.

ここに翻訳を挿入する

いずれかのページめくりボタンの真上から始めて、てこのツールまたは同様のプラスチック製の開封ツールを使用して、デバイスの背面をてこのように開けます。

ページめくりボタンを直接こじ開けようとしないでください。 ボタンが破損します。

最初の隙間をこじ開けるのに問題がある場合は、こじり具の平らな端を前から後ろのプレートの継ぎ目に沿って、隙間に滑り込むまで動かします。

ツールを奥深くまで差し込まないでください。デバイス端に搭載されているオレンジのフレックスケーブルを破損してしまうことがあります。

バックカバーを再装着する際は、まず下部の端をスライドしてからサイドから上部に向けてクリップを装着します。

-[* black] Starting just above one of the page-turning buttons, pry open the back of the device using a pry tool, or similar plastic opening tool.
-[* icon_caution] Do not attempt to pry directly on the page turning buttons. This will damage the buttons.
-[* icon_note] If you are having trouble getting an initial gap to pry from, run the flat edge of the pry tool along the front-to-back plate seam until it slips into a gap.
-[* icon_caution] Don't insert your tool too far, or you may damage some of the orange flex cables near the edges of the device.
+[title] Remove Rear Cover
+[* black] Turn the device upside-down and insert a pry tool between the two case pieces.
+[* icon_caution] On the left side just below the buttons there's a delicate ribbon cable that's part of the screen assembly and may be severed by a pry tool. (This is shown in the third photo, it's where the tool is pointing.) Regardless of where you start, stay clear of this area!
+[* icon_note] If you are having trouble getting an initial gap to pry from, run the flat edge of the pry tool along the front-to-back plate seam until it slips into a gap. You can also flex the device slightly and work a tool into one of the lower corners, which have a lot of empty space behind them rather than fragile components.
+[* icon_note] Looking at the back face, another safe place to start is on the right side just below the page turn buttons. (Note the green arrow in the board photo, which is rotated 90 degrees counter-clockwise.) The tool goes between the lower button and the hinge cover slot. If there isn't a slot there, you're on the wrong side!
+[* icon_caution] Do not attempt to pry directly on the page turning buttons.
+[* black] Work the pry tool around the edge of the case, releasing the 18 clips. Don't insert your tool too far, or you may damage components near the edges of the device. The clips are all in the outer edge of the backplate anyway. Note that the clip above the power switch is bigger and stronger than the rest.
+[* black] Pull the rear cover off. The remaining two clips near the center of the back are surprisingly strong, but they face in the same direction so don't just pull up. Instead slide the cover slightly towards the top of device to release them.
[* icon_reminder] When reinstalling the back cover, slide the bottom edge into place first, and then press up the sides and along the top until all the clips snap into place.

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります。