修理を始めるには コミュニティ ストア

iPhone 12 mini 여는 절차

注意：あなたは必要条件ガイドを編集しています。あなたが行なう変更は、この手順を含む全ての8個のガイドに反映されます。

ガイドに戻る
英語
韓国語
前の手順 次の手順

手順 4を翻訳中

手順4
iPhone 12 mini Opening Procedure: 手順 0、 3の画像 1 iPhone 12 mini Opening Procedure: 手順 0、 3の画像 2 iPhone 12 mini Opening Procedure: 手順 0、 3の画像 3

  • Support your iPhone on something sturdy such as a hardcover book so it rests hands-free and parallel to the ground; this makes it easier to work with in the following steps.

  • Use a hair dryer to heat along the bottom edge of the iPhone. The screen should feel slightly too hot to touch.

  • Wait one minute to give the adhesive a chance to release and present an opening gap.

  • Insert an opening pick under the screen's plastic bezel when the Anti-Clamp creates a large enough gap.

  • Make sure the opening pick is placed properly between the plastic bezel and the frame to avoid damaging your screen.

  • If the Anti-Clamp doesn't create a sufficient gap, apply more heat to the area and rotate the handle a quarter turn.

  • Don't crank more than a quarter turn at a time, and wait one minute between turns. Let the Anti-Clamp and time do the work for you.

  • Skip the next three steps.

양장본 책과 같은 튼튼한 물체 위에 iPhone을 받쳐서 핸즈프리 상태로 바닥과 평행하게 놓으면 다음 단계에서 작업하기가 더 쉬워집니다.

해어 드라이어를 사용하여 iPhone 하단 가장자리를 따라 가열하세요. 스크린이 만지기에는 약간 뜨거운 느낌이 들어야 합니다.

헤어 드라이어 사용법 지침은 이 안내서를 참조하세요.

접착제가 부드러워져서 틈이 생길 때까지 1분 정도 기다리세요.

안티클램프가 충분히 큰 틈을 만들면 스크린의 플라스틱 베젤 아랫면에 여는 픽을 끼우세요.

안티글램프가 충분한 간격을 만들지 못하면 해당 부위에 더 많은 열을 가하고 핸들을 1/4 바퀴 돌리세요.

한 번에 1/4 바퀴 이상 돌리지 말고 매회 돌리기 전에 약 1분 정도 기다린 후 돌리세요. 안티클램프와 시간이 알아서 일을 하도록 하세요.

다음 세 단계는 건너뛰세요.

[* black] Support your iPhone on something sturdy such as a hardcover book so it rests hands-free and parallel to the ground; this makes it easier to work with in the following steps.
-[* black] Use a hair dryer to heat along the bottom edge of the iPhone. The screen should feel slightly too hot to touch.
- [* icon_note] For complete instructions on how to use a hair dryer, [guide|157348|check out this guide|new_window=true].
+[* black] Use a [guide|157348|hair dryer|new_window=true] to heat along the bottom edge of the iPhone. The screen should feel slightly too hot to touch.
[* black] Wait one minute to give the adhesive a chance to release and present an opening gap.
[* black] Insert an opening pick under the screen's plastic bezel when the Anti-Clamp creates a large enough gap.
- [* icon_note] If the Anti-Clamp doesn't create a sufficient gap, apply more heat to the area and rotate the handle a quarter turn.
+ [* icon_caution] Make sure the opening pick is placed properly between the plastic bezel and the frame to avoid damaging your screen.
+[* icon_note] If the Anti-Clamp doesn't create a sufficient gap, apply more heat to the area and rotate the handle a quarter turn.
[* icon_caution] Don't crank more than a quarter turn at a time, and wait one minute between turns. Let the Anti-Clamp and time do the work for you.
[* black] ***Skip the next three steps.***

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります。