メインコンテンツにスキップ

注意:あなたはさきほど閲覧しているガイドの前提となるページを編集しています。あなたが行った変更は、この手順を含むガイド全体に影響を与えます。

英語
日本語

手順 14を翻訳中

手順14
Use scissors to cut one of your opening picks to about the width of the battery. Try not to leave any sharp corners. Insert the modified pick between the right side of the battery and the case. Use constant, steady pressure to slowly pry the battery up, separating it from the adhesive securing it to the system board.
  • Use scissors to cut one of your opening picks to about the width of the battery. Try not to leave any sharp corners.

  • Insert the modified pick between the right side of the battery and the case.

  • Use constant, steady pressure to slowly pry the battery up, separating it from the adhesive securing it to the system board.

  • Be careful not to deform or puncture the battery.

  • On the larger (42 mm) models, it's possible to accidentally pry at the system board underneath the battery. Insert the pick only far enough to get underneath the battery, not the system board.

  • If needed, apply a little high concentration isopropyl alcohol (90% or greater) around and under the battery to help weaken the adhesive.

  • Do not attempt to remove the battery as it is still connected.

バッテリー右側とケースの間にプラスチックの開封ツールを差し込みます。

システムボードにバッテリーを固定している接着剤を剥がしながらバッテリーを押し上げていきます。

バッテリーはまだ接続したままで、完全に取り外さないようにしてください。

[* black] Wedge a plasticUse scissors to cut one of your opening toolpicks to about the width of the battery. Try not to leave any sharp corners.
[* black] Insert the modified pick
between the right side of the battery and the case.
[* black] PryUse constant, steady pressure to ''slowly'' pry the battery up to separateup, separating it from the adhesive securing it to the system board.
[* icon_caution] Be careful not to deform or puncture the battery.
[* black] On the larger (42 mm) models, it's possible to [https://d3nevzfk7ii3be.cloudfront.net/igi/diYfGlClCsW1mXT2.full|accidentally pry at the system board|new_window=true] underneath the battery. Insert the pick only far enough to get underneath the battery, not the system board.
[* black] If needed, apply a little high concentration isopropyl alcohol (90% or greater) around and under the battery to help weaken the adhesive.
[* black] Wedge a plasticUse scissors to cut one of your opening toolpicks to about the width of the battery. Try not to leave any sharp corners.
[* black] Insert the modified pick
between the right side of the battery and the case.
[* black] PryUse constant, steady pressure to ''slowly'' pry the battery up to separateup, separating it from the adhesive securing it to the system board.
[* icon_caution] Be careful not to deform or puncture the battery.
[* black] On the larger (42 mm) models, it's possible to [https://d3nevzfk7ii3be.cloudfront.net/igi/diYfGlClCsW1mXT2.full|accidentally pry at the system board|new_window=true] underneath the battery. Insert the pick only far enough to get underneath the battery, not the system board.
[* black] If needed, apply a little high concentration isopropyl alcohol (90% or greater) around and under the battery to help weaken the adhesive.
[* icon_caution] '''Do not''' attempt to remove the battery as it is still connected.

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります