メインコンテンツにスキップ

はじめに

iOpenerは絶縁された、電子レンジで温めることができる保温バッグで、iPadや類似デバイスの先端に留められた接着剤を温めるために利用されます。

パーツ

パーツは指定されていません。

  1. 電子レンジに付着している汚れがiOpenerに付いてしまうことがあるので、使用前に電子レンジの底をきれいに拭き取ってください。 iOpenerを電子レンジ中央に置きます。
    • 電子レンジに付着している汚れがiOpenerに付いてしまうことがあるので、使用前に電子レンジの底をきれいに拭き取ってください。

    • iOpenerを電子レンジ中央に置きます。

    • 回転型の電子レンジ:iOpenerが電子レンジのターンテーブルで回転しているか確認してください。iOpenerが作動中に留まってしまうと、熱しすぎや焦げてしまいます。

    which temperature must be used for heating? Thx

    fbarletta - 返信

    I found you need to be very patient when using the iOpener. It's worth taking your time, giving the heat time to work on the glue. When I finally got the battery out, there were some strips of glue left behind that I just cleaned off with some isopropanol before installing the new battery.

    By the way, I had to run the iOpener for longer in my microwave for it to get hot enough. When it was too hot to touch, I figured it was hot enough for the batteries.

    Fredrik -

    I didn't find this to be as hard as I had built it up in my mind to be; HOWEVER, saying that I need to say years ago I was the local Nokia service center in my town. But many years ago right after they got rid of analog times. Yeah. A classic installer/repairer mistake when starting something they haven't fixed or installed before is picking up the instructions, flipping through them; maybe even reading a section that is new-then tossing the instructions over the shoulder. "I got this." This usually comes right before something major gets broke. And I can tell you when you try to do it yourself and then mess it up horribly then take it to the repair shop. Well we called that "I can do it myself" syndrome and charged extra to put back together what they brought in in the box. Now knowing all this - I can't stress this enough because I am stupid, stupid, stupid. COVER YOUR SCREEN IN CLEAR BOXING TAPE AND READ ALL THE INSTRUCTION BELOW THROUGH TO THE END BEFORE EVEN ATTEMPTING THIS FIX. Take my advise.

    windizy - 返信

    I didn't have an iOpener, so I used a wheat type heat bag. If you do this though, make sure you put a layer of plastic between your Mac and the bag, or you'll get condensation in places you don't want it.

    Martin Gray - 返信

    I started out using the iOpener but switched to my wife's hairdryer. A heat gun or hair dryer proved to be much more convenient and is a time saviour. You can heat more and the glue becomes more fluid make the next steps with the opening picks much easier

    Jan Van Puymbroeck - 返信

    Use a hair dryer! Watch this vid: https://youtu.be/16GkvjVyOJA It is much easier to do if you heat it from the other side.

    Fletcher Carpenter - 返信

    I know this is obvious, but backup your iPad with iTunes before you start. I'd also turn off your passcode if you have one.

    Laurie Higgins - 返信

    Ther first time you heat up the iOpener for this repair when its room temperature I had to heat it up for more than 30 seconds. I remember I had to heat it up for around 45 seconds. However, after that when you need to reheat it again during the repair 30 seconds will be enough.

    Yousef Ghalib - 返信

    Not everybody has a microwave. You need to state how long and at what temperature in a conventional oven.

    Esmond Pitt - 返信

    Hi, the microware have multiple power 1 to 9, what must be used ?

    Regards,

    Cedric

    Cedric VINCENT - 返信

    My microwave just died, can i heat it with boiled water?

    Alex COLOMBANI - 返信

    Taping as shown is impractical when using hair dryer method—tape simply comes off in the heat and gets in way of getting out the shards on the sides. If the thing wasn’t shattered, then taping unnecessary.

    B. A. Computer Services - 返信

  2. iOpenerを30秒温めます。
    • iOpenerを30秒温めます。

    • 修理作業中はiOpenerが冷めてしまいますので、使用毎に電子レンジに30秒入れて温めてからご利用ください。

    • 作業中、iOpenerを温めすぎないようにご注意ください。温めすぎるとiOpenerを破裂させてしまうことがあります。

    • 膨らんでいる状態のiOpenerは絶対に触らないでください。

    • 適切に温められたiOpenerは約10分間、温かい状態を保ちます。

    May I know the temperate limit about heating iOpener? (maximum 150 degrees Celsius?) thx so much.

    yamayhuang - 返信

    I had to heat mine up for more than 30 seconds. After 30 seconds on high it was only warm. It had to keep trying different times and checking it until it got hot. I think the initial time that I put it in for was over a minute.

    whale13 - 返信

    DO NOT USE IN NON ROTATING MICROWAVE! It will pop a hole. I had it in for 45 seconds the first time. It wasn't very hot inside and I saw it started to leak on the paper towel I put under it. Just a fair bit of advice. I think I will just stick with the heat gun. Loud but useful.

    Alex Jackson - 返信

    I don't own a microwave.

    mdanihy - 返信

    Its again waterproof when you change iphone 7 battery?

    Jon - 返信

    I don't have a microwave???

    Joe Blow - 返信

    30 sec at which equivalent watts setting and what temperature does iOpener heats up to for 30 secs. Only just bought it so needs info before using it. Thanks

    Sam Stieg - 返信

    can i use just ordinary microwave???

    juneseok kwon - 返信

    If I don't have a microwave then I try to use hot air gun so how many munuts i want to heat ?

    Mohideen Rifay - 返信

    I heated mine up for 30 seconds, tested, then again for 30 seconds. It felt adequately hot. Leaving it on the left side, per the instruction, for a minute did not loosen the adhesive. I ended up pulling the suction cup hard enough to shadder the old screen. Moral of the story, I don't think it gets hot enough safely to have an affect.

    Travis Dixon - 返信

    There is a clear problem here with the heating part using the iopener things....no details are given. Whoever is testing them needs to make it clear - What temperature does it need to be? And for which phone models, because they differ in what's needed. It's only £10-15 for a laser guided temp sensor unit, and the designers/repairers should have one of those already for doing these kinds of repairs. Explaining half a repair, is worse than not explaining at all :-(

    assortedrubbish - 返信

    I used a hot water bottle, works well as it covers the whole screen and stays hot for longer.

    dave - 返信

    If I may suggest include your microwave wattage so people can get an idea on time for there own

    Patrick Storey - 返信

    I ended up using a hair dryer. That iOpener thing took forever.

    mark fitzgerald - 返信

    30 seconds sure isn’t cutting it… 45 didn’t get the screen of my iPad air 2 to budge either… even after resting on the ipad for 4 minutes.

    60 seconds in the microwave, the iOpener burst.

    I’ll get a new one and try once more with heating it 45 seconds and repeat that for 30 minutes like others have said here. If that doesn’t work it’ll have to be the heat gun.

    K

    Karl Marble - 返信

    I can’t recommend the microwave. If the the iOpener becomes too hot, it bursts. Better put the opener in cooking water. Dry it and use it. Instead of an iOpener you can use hot/cool packs as well.

    Bernhard Keim - 返信

    Trust the directions! I forgot and left it in the Microwave too long and after 1 minute I had Mt Vesuvius - the iOpener burst and spewed the goodies out. The problem is, the Digitizer can be damaged by a hot air gun, so I had to tough out and remove the glue the hard way. I made it … with lots of patience! Tough lesson.

    Larry Bennett - 返信

    I also used a hairdryer. I used it on the low setting and I cut a piece of carboard to protect the rest of the screen. The iFixit tool and method is vert tedious and very time consuming in comparison. With the hairdryer method you can literally have the display apart in a few minutes. Using your other hand nearby the area you are heating it should be very hot but not enough to burn your hand. You only have to heat metal part of case near glass edge. If you have a cellular model then you need to be very careful because the black antenna area is plastic. So less heat and work your way up in adding heat just enough to separate around the area but not so much you melt the plastic!

    Fixrights - 返信

  3. iPhoneのバッテリーキット

    Only $29.99

    Buy Now

    iPhoneのバッテリーキット

    Only $29.99

    Buy Now
  4. 電子レンジからiOpenerを取り出します。iOpenerの中央は熱くなっているため、両端の平面になっている部分を持ってください。
    • 電子レンジからiOpenerを取り出します。iOpenerの中央は熱くなっているため、両端の平面になっている部分を持ってください。

    • iOpenerは大変熱くなっていることがあります。必要であれば、オーブン用のミトンカバーをご利用ください。

    Will a hair dryer work for heating the glass?

    Me berg - 返信

    Can you use an oven instead?

    Rafael -

    Yes, as does a heat gun.

    anonymous 4602 - 返信

    I did this repair. I used a hair dryer, I think it works better: gets very hot fast.

    Cobus de Beer - 返信

  5. iOpenerの何も表示がない裏側を下にしてデバイスの接着剤を取り外したい部分の上部に当てます。適度な温度に温まり、 iOpener内部の液体が平らになっているか確認してください。 フロントパネルを開封する前に約90秒間、デバイスに iOpenerを当てます。 この時点で、プラスチック製の開封ツールを使って、スクリーン下をこじ開け始めます。どこをどのように作業を進めていくかはそれぞれの修理ガイドをご覧ください。
    • iOpenerの何も表示がない裏側を下にしてデバイスの接着剤を取り外したい部分の上部に当てます。適度な温度に温まり、 iOpener内部の液体が平らになっているか確認してください。

    • フロントパネルを開封する前に約90秒間、デバイスに iOpenerを当てます。

    • この時点で、プラスチック製の開封ツールを使って、スクリーン下をこじ開け始めます。どこをどのように作業を進めていくかはそれぞれの修理ガイドをご覧ください。

    • 作業中、 iOpenerを再度温める必要があります。 iOpenerを温めすぎないようにするには、 iOpenerを触って完全に冷たくなるまで待つことです。電子レンジに30秒以上入れないでください。

ゴール

331 の人々がこのガイドを完成させました。

以下の翻訳者の皆さんにお礼を申し上げます:

100%

これらの翻訳者の方々は世界を修理する私たちのサポートをしてくれています。 あなたも貢献してみませんか?
翻訳を始める ›

Andrew Optimus Goldheart

メンバー登録日: 2009年10月17日

414,551 ポイント

411のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

101 メンバー

8,661のガイドは作成済み

I bought two of these, and I can't get an iPad 2 to open using the iOpener; I'm going to keep trying, but heads up, it's not as easy as 1-2-3. I'll update if I get it to work.

Kevin McCartney - 返信

I used a flat toaster maker and turned it off and on as required, Fixed my Ipad mini ok.

Chris Newman -

Step 2 says to wait 5 minutes between reheating, step 4 says to wait 3 minutes.

Also, do you sell the "this is a microwave" stickers? xD

Mark Brown - 返信

Will this tool damage the lcd/ pixels or even the camera/sensor if placed on the edge above those? I need to soften up the adhesive only, not replacing the screen at all. I have a surface pro 4.

allanwl - 返信

A short remark about how much force will then be needed to separate the old battery from the heated adhesive would be helpful. I found that even after I was able to begin the insertion of a plastic card between the battery and the case, it required a great deal of force to push the card further under the battery to complete the separation.

Steven Aigner - 返信

While the iOpener tool kit may be the best solution for some applications it is decidedly NOT the optimal tool for removing and replacing a badly cracked Samsung S7 back. The iOpener was simply unable to get the adhesive hot enough to get it to release. Also, the cracked back did not provide enough uninterrupted surface for the suction cap to maintain enough suction to lift the back after I heated it with a heat gun. Overall an EXTREMELY frustrating experience. I do not fault iFixit for this but there could be a little more nuanced explanation about which applications are the best fit for the kit. Mostly I’d like to send a big effuuu to Samsung and all the other smart phone manufacturers who are systematically locking end user out of their purchases. Setting aside the sealed backs it’s absurd that we spend $700 on a smart phone and then have to spend another $40-60 for a protective case and a screen protector. The is no other consumer good we would put up with this.

Alain - 返信

I absolutely could not agree more, Alain.It’s a %#*@ joke what they charge for Data too, just criminal.

nwrrshow -

Thanks Andrew! :-)

Tony - 返信

If I have no microwave, is there a way to heat the iOpener in a hot-air baking oven? If ‘yes’, at what temperature and how long? Thx

Andreas Horn - 返信

Hi there Andreas! Do not place the iOpener directly in an oven on on a stovetop. If you don’t have a microwave, you can place the iOpener in boiling water for about a minute (if you place the iOpener inside a temperature-safe plastic bag you can keep it dry and make it a bit easier to remove from the hot water. Don’t place a wet iOpener on your electronics, and try to handle the iOpener only by the tabs on the end, especially if using sharp tongs to remove it from the water.

Sam Goldheart -

Is there any other ways to heat the iopener other than using a microwave

nixon nelson - 返信

Hi Nixon, if you don’t have a microwave, the safest heating method will be to place the iOpener in boiling water for about a minute (if you place the iOpener inside a temperature-safe plastic bag you can keep it dry and make it a bit easier to remove from the hot water. Don’t place a wet iOpener on your electronics, and try to handle the iOpener only by the tabs on the end, especially if using sharp tongs to remove it from the water.

Sam Goldheart -

iPad Air (Gen. 1) - Broken Screen

To this day, I have followed the procedure multiple times to heat the adhesive in order to remove the screen, yet it has yet to allow me even just one pick under the screen. What could possibly be going on? I’ve placed packing tape on the screen due to high fracture but that’s all.

Gavin Starr - 返信

コメントを追加する

統計データを表示:

過去 24時間: 105

過去 7 日: 779

過去 30 日: 3,498

今までの合計 192,315