はじめに

The iMac G3 Uses a 3.5" IDE Hard Drive. It supports data partitions no larger then 128GB and boot partitions no larger then 8GB (The 8GB limit only applies to iMac G3 tray loaders).

  1. The iMac G3. This was a great computer for the time, and had plenty of features.
    • The iMac G3. This was a great computer for the time, and had plenty of features.

    コメントを追加する

  2. Start by flipping the iMac upside-down. It may help to lay it on a towel, so you don't damage the screen, or scratch the face.
    • Start by flipping the iMac upside-down. It may help to lay it on a towel, so you don't damage the screen, or scratch the face.

    コメントを追加する

    • Remove this Phillips screw.

    • Using a flathead screwdriver, work your way around the bottom cover, until it comes off.

    • Then, lift the bottom cover up and out, and set it aside.

    コメントを追加する

    • Now, remove the DB-15 Video connector from the logic board.

    • It may be helpful to use a Phillips screwdriver to remove the thumbscrews.

    コメントを追加する

    • Remove the power cable from the logic board assembly.

    コメントを追加する

    • Remove the front panel connector.

    コメントを追加する

  3. 20ドル以上のお買い上げで送料無料(米国内にお住まいの方対象)
    お支払い手続きの際にはクーポンコードBLUEANDBLACKを入力してください。(米国内にお住まいの方対象)
    20ドル以上のお買い上げで送料無料(米国内にお住まいの方対象)
    クーポンコードBLUEANDBLACKをご使用ください。(米国内にお住まいの方対象)
    • Now, remove these Phillips screws.

    • Now, grab the logic board assembly by the piece of plastic, and lift it out.

    コメントを追加する

    • The logic board assembly. This is the heart of the computer, it contains the motherboard, CPU, RAM, V-RAM, PRAM battery, the hard drive, and the optical drive.

    コメントを追加する

    • Now to remove the optical drive!

    コメントを追加する

    • The optical drive is located near the front of the assembly.

    コメントを追加する

    • To remove the drive, push it in, lift up, and then pull forward.

    • As you pull the drive forward, disconnect the ribbon cable and set it aside.

    コメントを追加する

    • Remove the two phillips #00 screws.

    • Then remove the board. This will reveal that it is a standard PATA drive.

    • Congrats, the drive is free! You can use any PATA-tray loading drive in the iMac G3 which means you can install a CDRW to burn CDs in OS9 or X(if using OSX,install that DVD writer) but, of course only original drives will match the great look of the iMac).

    コメントを追加する

    • Hard Drive Removal:

    コメントを追加する

    • Start by removing these Phillips screws:

    • Now, remove all of these cables:

    コメントを追加する

    • Now, remove the optical drive retention spring.

    • Push in on both sides, and pull towards you releasing the retention spring.

    • It may help to do it one side at a time.

    コメントを追加する

    • Now lift the drive up, and pull it out.

    • Make sure that no cables are snagged before completed pulling out the drive!

    コメントを追加する

    • When installing a new drive, make sure that the drive jumper block is set to "Single drive". In most drives, this means removing the jumper, or positioning the jumper horizontally instead of vertically, so you don't lose it.

    • To remove the drive from the metal caddy, remove these four screws from the side of the drive.

    コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

29 の人々がこのガイドを完成させました。

Chris Green

メンバー登録日: 2009年10月11日

32,579 ポイント

45のガイドは作成済み

チーム

Master Techs Master Techs人のメンバー

Community

278 メンバー

756のガイドは作成済み

great description, great photos

antiquarian1 - 返信

Many thanks. Worked perfectly.

Bob Schowalter - 返信

is the hard disk on a mac interchangeable to iMac 4984 from iMac M5521? Power supply failed on M5521. thx

alexa pritchard - 返信

コメントを追加する

統計データを表示:

過去 24時間: 9

過去 7 日: 33

過去 30 日: 172

今までの合計 30,460