メニュー

あなたの設定

私のワークベンチ

お持ちのデバイス用の修理ガイド、交換用パーツやアンサーフォーラムにアクセスする。
カート

カートには何も入っていません。

当社のショップを閲覧する

Xbox Disc Drive Replacement

作成者： rmarstel (そして 8 人のその他投稿者)
  • コメント: 6
  • お気に入り: 48
  • 完了: 43

難易度

簡単

手順

12

所要時間

15 - 20 分

セクション

2

フラグ

0

はじめに

Use this guide to replace the disk drive in a Microsoft Xbox.

ツール

これらのツールを購入する

パーツ

パーツは必要ありません。

  1. Make sure your Xbox is safely unplugged and is laying on a flat, stable surface.

    • Make sure your Xbox is safely unplugged and is laying on a flat, stable surface.

    翻訳

  2. Turn the Xbox over to reveal the four rubber feet.

    • Turn the Xbox over to reveal the four rubber feet.

    • Use a metal spudger to pry off the four rubber feet.

    翻訳

  3. There are 2 more screws hidden under the two labels on the bottom of the case. You can either remove the labels or simply feel for the screw holes through the labels and then cut or punch a hole through them.

    • There are 2 more screws hidden under the two labels on the bottom of the case.

    • You can either remove the labels or simply feel for the screw holes through the labels and then cut or punch a hole through them.

    翻訳

  4. Remove the six T20 Torx screws securing the top cover to the bottom cover.

    • Remove the six T20 Torx screws securing the top cover to the bottom cover.

    翻訳

  5. Pro Tech ツールキットを含むご注文、もしくは総額 $100ドル以上のご注文については送料無料です。

    当社のショップを閲覧する

  6. Wedge a metal spudger and carefully pry upwards to slightly separate the top and bottom covers. Flip the Xbox right side up.

    • Wedge a metal spudger and carefully pry upwards to slightly separate the top and bottom covers.

    • Flip the Xbox right side up.

    • Hold the sides and lift the Xbox slightly off the bench. A gentle shake of the unit should see the top cover separate from the rest of the unit quite easily.

    • Placing the Xbox on your lap while separating the top and bottom covers may make the process easier.

    翻訳

  7. Once the bottom and top shells are no longer attached, carefully turn the Xbox right-side-up, lift and remove the top cover. Once the bottom and top shells are no longer attached, carefully turn the Xbox right-side-up, lift and remove the top cover.

    • Once the bottom and top shells are no longer attached, carefully turn the Xbox right-side-up, lift and remove the top cover.

    翻訳

  8. Remove the three 3 mm T10 screws securing the hard drive to the Xbox. There is one screw on the rear left side of the hard drive that is only visible when the IDE ribbon cable is lifted up. The other two are at the front right and left sides of the hard drive.

    • Remove the three 3 mm T10 screws securing the hard drive to the Xbox.

    • There is one screw on the rear left side of the hard drive that is only visible when the IDE ribbon cable is lifted up. The other two are at the front right and left sides of the hard drive.

    • The screw on the lower left corner of the disk drive is not in the hole that it appears to be in, but rather just closer to the corner.

    翻訳

  9. Free the hard drive power cable from the carrier for sufficient slack to lift the hard drive out. Lift the plastic hard drive carrier out of the Xbox case.

    • Free the hard drive power cable from the carrier for sufficient slack to lift the hard drive out.

    • Lift the plastic hard drive carrier out of the Xbox case.

    翻訳

  10. Remove the four 3.4 mm T15 Torx screws from the plastic hard drive carrier (two screws per side). Carefully remove the hard drive from the plastic carrier. Gentle rocking will see the hard drive come out quite easily. Carefully remove the hard drive from the plastic carrier. Gentle rocking will see the hard drive come out quite easily.

    • Remove the four 3.4 mm T15 Torx screws from the plastic hard drive carrier (two screws per side).

    • Carefully remove the hard drive from the plastic carrier. Gentle rocking will see the hard drive come out quite easily.

    翻訳

  11. Pull both the hard drive data ribbon cable and the power cable straight up from the hard drive. They may be firmly seated, so be careful trying to remove them. DO NOT pull the wires as you may damage the cable assembly.

    • Pull both the hard drive data ribbon cable and the power cable straight up from the hard drive.

    • They may be firmly seated, so be careful trying to remove them. DO NOT pull the wires as you may damage the cable assembly.

    翻訳

  12. Remove the disk drive. It should come right out. Unplug the ribbon cable and yellow cables from back of disk drive. Unplug the ribbon cable and yellow cables from back of disk drive.

    • Remove the disk drive. It should come right out.

    • Unplug the ribbon cable and yellow cables from back of disk drive.

    翻訳

  13. Pry back the black plastic tabs around the disk drive in order to remove it from its housing. Once removed, set the drive aside.

    • Pry back the black plastic tabs around the disk drive in order to remove it from its housing. Once removed, set the drive aside.

    • ONLY REMOVE IF DEAD!

    翻訳
まとめ

To reassemble your device, follow these instructions in reverse order.

43 の人々がこのガイドを完成させました。

作成者

8他の投稿者と一緒に

rmarstel

メンバー登録日: 2009年10月29日

3,775 ポイント

5のガイドは作成済み

バッジ: 15

+12 個以上のバッジ

チーム

Cal Poly, Team 18-2, Maness Fall 2009 Cal Poly, Team 18-2, Maness Fall 2009人のメンバー

CPSU-MANESS-F09S18G2

3 メンバー

10のガイドは作成済み

コメント1件

コメントを追加

http://www.ebay.com/gds/How-To-Determine...

Utilize the information on this website to determine what Xbox version you have so you know what replacement parts to look for.

Navy Vet 2015 - 返信

コメントを追加する

1024

統計データを表示:

過去 24時間: 9

過去 7 日: 43

過去 30 日: 229

今までの合計 45,247