メインコンテンツにスキップ

パーツ

パーツは指定されていません。

  1. Remove the six screws located on the underside of the system using the Gamebit 4.5mm screwdriver.
    • Remove the six screws located on the underside of the system using the Gamebit 4.5mm screwdriver.

  2. Carefully flip the unit back over. Locate the seam. Lift and separate the upper half of the case from the lower half of the case. Locate the seam. Lift and separate the upper half of the case from the lower half of the case.
    • Carefully flip the unit back over.

    • Locate the seam. Lift and separate the upper half of the case from the lower half of the case.

  3. Remove the two 11.7 mm Phillips #2 screws connecting the power switch to the motherboard.
    • Remove the two 11.7 mm Phillips #2 screws connecting the power switch to the motherboard.

  4. The power switch is connected to the motherboard near the top left of the console. Carefully pull the connector from its socket on the motherboard. You may need to wiggle it out as you pull.
    • The power switch is connected to the motherboard near the top left of the console.

    • Carefully pull the connector from its socket on the motherboard. You may need to wiggle it out as you pull.

    • Do not detach the connector by pulling on the wires. This could damage the wires or the socket.

  5. Lift the right side of the eject lever out of the housing. Lift the right side of the eject lever out of the housing.
    • Lift the right side of the eject lever out of the housing.

  6. Pull the metal bar out through the right side of the eject lever. Make sure to keep track of the spring located on the left side of the lever as it may shoot off when removing the metal bar. When reassembling, the procedure becomes more difficult due to the spring (marked red). We recommend that one person hold the spring in place (picture 3) while another person slides the metal bar back into the left housing, and slide the eject lever onto the metal bar.
    • Pull the metal bar out through the right side of the eject lever.

    • Make sure to keep track of the spring located on the left side of the lever as it may shoot off when removing the metal bar.

    • When reassembling, the procedure becomes more difficult due to the spring (marked red). We recommend that one person hold the spring in place (picture 3) while another person slides the metal bar back into the left housing, and slide the eject lever onto the metal bar.

  7. Lift the controller ports out of the housing, this should be done without much force. Take note of the location of the ribbon cable connection.
    • Lift the controller ports out of the housing, this should be done without much force. Take note of the location of the ribbon cable connection.

  8. Carefully remove the ribbon cable from its port. Carefully remove the ribbon cable from its port.
    • Carefully remove the ribbon cable from its port.

  9. Remove the two Phillips two 11.6mm screws that connect the front shield to the motherboard.
    • Remove the two Phillips two 11.6mm screws that connect the front shield to the motherboard.

  10. Lift the front shield straight up to remove it from the motherboard.
    • Lift the front shield straight up to remove it from the motherboard.

  11. Remove the two silver 15.6 mm Phillips #2 screws on either side of the 62 pin connector.
    • Remove the two silver 15.6 mm Phillips #2 screws on either side of the 62 pin connector.

  12. Remove the  11.8 mm Phillips #2 screw near the rear of the SNES.
    • Remove the 11.8 mm Phillips #2 screw near the rear of the SNES.

  13. Lift the motherboard straight up to remove it.
    • Lift the motherboard straight up to remove it.

終わりに

To reassemble your device, follow these instructions in reverse order.

30 の人々がこのガイドを完成させました。

Melina

メンバー登録日: 2010年10月12日

787 ポイント

1ガイドが承認済み

チーム

Cal Poly, Team 4-47, Amido Fall 2010 Cal Poly, Team 4-47, Amido Fall 2010人のメンバー

CPSU-AMIDO-F10S4G47

4 メンバー

10のガイドは作成済み

3 件のコメント

There are several versions of the Super Nintendo. Steps for my version are a bit different.

joshenders - 返信

This seems to be a newer super nintendo. If you have one of the older ones, there will be a bit more screws but still basically the same steps.

Anonymous Idea -

It’s possible they may be referring to the European/Japanese version of the Super Nintendo/Super Famicom. Either that, or it’s one of the weird, misshapen “reskins”.

Rupin Soland - 返信

コメントを追加

統計データを表示:

過去 24時間: 5

過去 7 日: 51

過去 30 日: 249

今までの合計 48,734