はじめに

This guide shows all the steps leading up to, and including, the removal of the motherboard.

Apply pressure to the back cover and slide it forward towards the camera.
  • Apply pressure to the back cover and slide it forward towards the camera.

  • Lift the back cover off the phone.

コメントを追加する

Holding the phone firmly, use the notches to grip and lift up the battery.
  • Holding the phone firmly, use the notches to grip and lift up the battery.

コメントを追加する

Remove the four 4.45mm screws at the corners of the phone.
  • Remove the four 4.45mm screws at the corners of the phone.

コメントを追加する

Use the plastic opening tool to unhinge the locks around the edges of the phone. Do not worry about the inner components of the phone; they are not connected to this case.
  • Use the plastic opening tool to unhinge the locks around the edges of the phone.

  • Do not worry about the inner components of the phone; they are not connected to this case.

コメントを追加する

Lift the casing off of the phone.
  • Lift the casing off of the phone.

コメントを追加する

With the screws removed, locate the antenna.
  • With the screws removed, locate the antenna.

コメントを追加する

Using a Phillips head screwdriver, remove the 4.50mm screw holding the antenna in place.
  • Using a Phillips head screwdriver, remove the 4.50mm screw holding the antenna in place.

コメントを追加する

Using the plastic opener tool, squeeze gently on the antenna cable connector and lift to remove the connector from its position.
  • Using the plastic opener tool, squeeze gently on the antenna cable connector and lift to remove the connector from its position.

コメントを追加する

Gently lift up on the antenna and remove it from the back of the device.
  • Gently lift up on the antenna and remove it from the back of the device.

コメントを追加する

Remove the two 3.50mm screws connecting the motherboard to the case.
  • Remove the two 3.50mm screws connecting the motherboard to the case.

コメントを追加する

Use the plastic opener tool to detach the three ribbons on the motherboard. Use the plastic opener tool to detach the three ribbons on the motherboard. Use the plastic opener tool to detach the three ribbons on the motherboard.
  • Use the plastic opener tool to detach the three ribbons on the motherboard.

コメントを追加する

Lift out the top right ribbon from its slot on the motherboard.
  • Lift out the top right ribbon from its slot on the motherboard.

コメントを追加する

Use the plastic opener tool to unhinge the the locks on the side of the motherboard connecting it to the front casing. Use the plastic opener tool to unhinge the the locks on the side of the motherboard connecting it to the front casing.
  • Use the plastic opener tool to unhinge the the locks on the side of the motherboard connecting it to the front casing.

コメントを追加する

Lift the motherboard away from the front casing.
  • Lift the motherboard away from the front casing.

コメントを追加する

After removing lifting up on the motherboard, the front casing and center frame should be separated as shown.
  • After removing lifting up on the motherboard, the front casing and center frame should be separated as shown.

コメントを追加する

Using the plastic opener tool, gently pry away the side strip control buttons from the metal center frame. There are three strips total: one on the right, left, and top of the phone. There are three strips total: one on the right, left, and top of the phone.
  • Using the plastic opener tool, gently pry away the side strip control buttons from the metal center frame.

  • There are three strips total: one on the right, left, and top of the phone.

コメントを追加する

Using the plastic opener tool, pry the speaker connector away from the back of the motherboard.
  • Using the plastic opener tool, pry the speaker connector away from the back of the motherboard.

コメントを追加する

Using the plastic opener tool, remove the speaker from its setting.
  • Using the plastic opener tool, remove the speaker from its setting.

  • Pry where the wire enters the speaker.

  • The speaker has adhesive on the bottom, thus removing it will require a bit of wiggling.

コメントを追加する

Gently lift the motherboard from the center frame.
  • Gently lift the motherboard from the center frame.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

Brayton

メンバー登録日: 2011年10月12日

40 ポイント

4のガイドは作成済み

チーム

Cal Poly, Team 3-13, Regan Fall 2011 Cal Poly, Team 3-13, Regan Fall 2011人のメンバー

CPSU-REGAN-F11S3G13

4 メンバー

16のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 4

過去 30 日: 14

今までの合計 4,736