はじめに

First you take the front apart and then you take the back apart in order to get to the hinge.

push down the back cover of the phone, then take it out.
  • push down the back cover of the phone, then take it out.

コメントを追加する

Remove the battery.
  • Remove the battery.

コメントを追加する

Remove the two 4 mm screws on screen.
  • Remove the two 4 mm screws on screen.

コメントを追加する

Remove front outside casing with plastic opening tools. Remove front outside casing with plastic opening tools.
  • Remove front outside casing with plastic opening tools.

コメントを追加する

Remove ribbon connector next to camera using tweezers.
  • Remove ribbon connector next to camera using tweezers.

コメントを追加する

Unscrew and remove the two 3.95 mm screws underneath that ribbon connector.
  • Unscrew and remove the two 3.95 mm screws underneath that ribbon connector.

  • Be careful not to lose their accompanying plastic washers.

コメントを追加する

Pull the two halves of the phone apart. The phone will not slide straight apart. You have to angle the back half up a little.
  • Pull the two halves of the phone apart.

  • The phone will not slide straight apart. You have to angle the back half up a little.

  • Do not force it. Jiggle it a little if it doesn't come apart.

コメントを追加する

Remove the plastic panel cover from the hinge.
  • Remove the plastic panel cover from the hinge.

コメントを追加する

Remove the 3.41 mm screw out from underneath plastic cover. Remove the 3.41 mm screw out from underneath plastic cover.
  • Remove the 3.41 mm screw out from underneath plastic cover.

コメントを追加する

Pop out top half of hinge with plastic opening tool. This will release hinge cover for removal. Pop out top half of hinge with plastic opening tool. This will release hinge cover for removal.
  • Pop out top half of hinge with plastic opening tool. This will release hinge cover for removal.

コメントを追加する

Pull off hinge cover. Pull off hinge cover.
  • Pull off hinge cover.

コメントを追加する

Remove the two 2.71 mm screws on the hinge using screwdriver. Under these screws will be a washer, spring, and small metal disc. Make sure you don't lose these.
  • Remove the two 2.71 mm screws on the hinge using screwdriver.

  • Under these screws will be a washer, spring, and small metal disc. Make sure you don't lose these.

コメントを追加する

Remove Verizon logo from back of phone using plastic opening tool
  • Remove Verizon logo from back of phone using plastic opening tool

  • The logo is attached with glue. It will be sticky but it just pulls off.

コメントを追加する

Remove the four 4.44 mm screws from the back.
  • Remove the four 4.44 mm screws from the back.

  • Remove the three 4.35mm screws from under the Verizon logo.

  • Make sure you don't mix the screws together.

コメントを追加する

Pull back off using plastic opening tool
  • Pull back off using plastic opening tool

  • Do Not lose the buttons on the side of the phone, as they will come off of the phone when you remove the back outside casing.

コメントを追加する

Pull up on yellow tab.
  • Pull up on yellow tab.

コメントを追加する

Disconnect connecting cord using tweezers.
  • Disconnect connecting cord using tweezers.

コメントを追加する

Disconnect rectangular ribbon.
  • Disconnect rectangular ribbon.

コメントを追加する

Take out the logic board.
  • Take out the logic board.

コメントを追加する

Remove the three 3.95 mm screws.
  • Remove the three 3.95 mm screws.

  • The two rightmost screws must be pulled out with tweezers after unscrewed.

コメントを追加する

Pull the hinge out.
  • Pull the hinge out.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Chris

メンバー登録日: 2011年04月16日

133 ポイント

10のガイドは作成済み

チーム

Cal Poly, Team 12-35, Maness Spring 2011 Cal Poly, Team 12-35, Maness Spring 2011人のメンバー

CPSU-MANESS-S11S12G35

4 メンバー

10のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 8

今までの合計 3,998