修理を始めるには コミュニティ ストア

Protocol Videodrone AP Battery Wiring Replacement

はじめに

This guide will show you how to replace the battery and the soldering new wires to the motherboard. This is guide includes a highly recommend soldering guide. CAUTION: Soldering iron will be hot and may cause minor burns if handles improperly.

必要な工具と部品

  1. Protocol Videodrone AP Battery Wiring Replacement, Battery Wiring: 手順 1、 1の画像 1

    • Make sure the drone is turned off

    翻訳

  2. Protocol Videodrone AP Battery Wiring Replacement: 手順 2、 1の画像 1

    • Open the hatch and carefully pull out the battery to expose the cable connection

    翻訳

  3. Protocol Videodrone AP Battery Wiring Replacement: 手順 3、 2の画像 1 Protocol Videodrone AP Battery Wiring Replacement: 手順 3、 2の画像 2

    • Carefully pull apart the cable connection

    翻訳

  5. Protocol Videodrone AP Battery Wiring Replacement: 手順 4、 2の画像 1 Protocol Videodrone AP Battery Wiring Replacement: 手順 4、 2の画像 2

    • Unscrew the 4 screws from the bottom of the drone.

    • Unscrew the 8 screws connecting the propeller guards to the drone

    • Unscrew the four propeller screws.

    • One screw is hidden behind the screwdriver.

    翻訳

  6. Protocol Videodrone AP Battery Wiring Replacement: 手順 5、 1の画像 1

    • Carefully remove faulty battery wiring from the drone

    翻訳

  7. Protocol Videodrone AP Battery Wiring Replacement: 手順 6、 1の画像 1

    • Feed through opening using tweezers to grasp the wire and carefully pull through.

    翻訳

  8. Protocol Videodrone AP Battery Wiring Replacement: 手順 7、 1の画像 1

    • Use the soldering iron to solder new wires to mother board. CAUTION: Soldering iron may get hot and cause minor burns if handled improperly.

    • Use this guide for how to solder: https://www.youtube.com/watch?v=QKbJxytE...

    翻訳

  9. Protocol Videodrone AP Battery Wiring Replacement: 手順 8、 1の画像 1

    • Reattach the battery and test for power by turning on the drone and look for the 4 LEDs turn on.

    翻訳
終わりに

All Done!

ある他の人がこのガイドを完成しました。

作成者

4人の作成者と共同で作成されました。

Serge

メンバー登録日: 09/26/17

340 ポイント

3のガイドは作成済み

バッジ: 8

+5 個以上のバッジ

チーム

USF Tampa, Team S2-G1, Passmore Fall 2017 USF Tampa, Team S2-G1, Passmore Fall 2017人のメンバー

USFT-PASSMORE-F17S2G1

4 メンバー

3のガイドは作成済み

3 件のコメント

Great explanation. Just wondering where to get the replacement piece. My drone has the black wire hanging by a single strand just outside the white connector. The red wire is in tact but I would need the whole part that attaches to the board and extends outside the drone to connect the battery to. Thanks

yasureok - 返信

Was wondering i think its charging the blue light flashes when plugged in but wont turn on. Wires look brand new

Michael Landry - 返信

I’m wondering the same thing, mine lights up blue when charging, wires look good but still no action.

Ryann Hunter -

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 4

今までの合計 1,761