はじめに
PS4が酷使され、絶えず過熱していて、ファンを交換したくなった場合、以下の手順に従ってください。ハードディスクを除くいかなる交換や分解もソニーの保証を受けられなくなるので注意してください。
マザーボードを外すとCPUとヒートシンクの間に塗られている放熱グリスが剥がれます。デバイスを再度組み立てる前に新しい放熱グリスを塗りなおしてください。このガイドを参照して、作業を進めてください。
ツール
ビデオの概要
-
-
PS4の背面から9mmセキュリティートルクスネジTR9を4本外します。
Depending on the model of PS4, (i.e. CHU-1001A vs. CHU-1215A) it may only have the two screws in the center, not the edge ones.
Sawyer Coe - 返信
-
-
-
電源からコネクターを外します。
-
電源ユニットを持ち上げてケースから外します。
you need to lift the power board/box up vertically first as there are 2 long prongs extending up into the box. if you try to lift just one end you will bend the prongs.
has anyone used any of these guys, i don't fancy doing it
during this step it exposes a black phillips head screw at least on some models(such as mine) this screw mates the metal sandwich around the motherboard together. I was unable to perform step 19 until I released this Black short Phillips screw.
I just came across this screw at the same time. It is extremely stuck and I'm afraid to strip it. Any ideas?
This is a poor instruction. Obviously you need to lift the psu out first but on my white ps4 it simply won't budge on one side. Now I'm stuck already.
Rainer, look at pollytintop’c comment. Lift vertically and you will get to next step. I used a screwdriver on the side opposite the fan, but I am a savage in many ways. If you insist on treating it delicately a small suction or powerful tape might work.
We may not all make it back. Good luck
Guten Tag,
an dem Mainboard meiner PS4 ist die Buchse mit den Metallstücken drin, wo man den Stecker des Netzteils reinsteckt, abgebrochen. Als ich das Netzteil rausnehmen wollte, habe ich viel zu fest gezogen und nun ist es ab.
Bilder: https://imgur.com/a/hIMeWTh
Welche Methoden gäbe es dieses Problem zu beheben?
Mit freundlichen Grüßen
-
-
-
金属製のリリースタブを押して、リボンワイヤーを慎重に引き抜いて、光学ドライブからリボンワイヤーの接続を外します。力を入れる必要はありません。
-
マザーボードから同じリボンワイヤーの接続を外します。必ず金属製のリリースタブを押して、リボンワイヤーを慎重に引き抜いてください。
If your PS4 eject button doesn’t respond/work and it doesn’t accept discs ( it doesn’t beep or nothing happens when you touch the eject button and it doesn’t make noise when you try to put a disc in and doesn’t take it) it could be because you took the wire ribbon out the optical drive or motherboard the wrong way and did not press down on the metal tab. ( like I did ) the wire ribbon should have these tiny “wings” on both sides and on both ends. Easy and very cheap fix. Ordered a new ribbon wire on amazon for $12!!! Better then buying a new PS4!!!!
Any way to get one of those wings out ? One of them broke off as I was pulling the cable out and is stuck.
-
-
-
9mmTR9セキュリティートルクスネジを4本外します。
-
5mm#1プラスネジを外します。
Mine on the bottom right near the board was a 5mm Phillips #1 instead of the expected 9mm Torx screw. Also, I have a shield plate covering my (or my customer's) board here.
Mine is the same
Jesse King - 返信
Model Cuh1001a
Jesse King - 返信
-
-
-
上部カバーの前を持ち上げて、後方にスライドさせます。
my right corner, by the ps4 logo, was VERY snug, it took me a few minutes to pop that corner off, took a decent amount of force to pop it off
theyoonion - 返信
-
-
-
9mm#1プラスネジを2本外します。
-
金属製サポートブラケットを外します。
Danach muss auf der Innenseite noch eine schwarze Schraube gelöst werden, sonst kann man die Abdeckung und auch nicht Mainboard lösen.
-
-
-
金属製のカバーを持ち上げて外します。
On some PS4 consoles there is a small black Phillips head screw under the PSU securing the metal cover to the midframe of the console. If you do not remove this screw you will not be able to remove the metal cover, and run the risk of damaging it, or the motherboard.
-
-
-
マザーボードから3本のワイヤープラグを慎重に引き上げて、外します。
What can i do if i broke these three little prongs?
2 options 1 make a new contact, 2 buy a New fan as it is The fan contact ;)
-
-
-
本体からマザーボードを持ち上げて、取り外します。
Unfortunately it costs more for the motherboard and optical drive together than it costs for a new PS4 1TB with a game
-
-
-
ファンが見える状態になったので、9mm#1プラスネジを2本外します。
-
右上に3本目のネジがあれば、それも外します。
-
交換のためにファンを持ち上げて外します。
The guide here is wrong, the left screw holding the fan down is also the bottom-most screw holding the step 22 metal cover down. The only screws that should be on the fan at Step 23 should be the lower right screw and upper right screw
Haybale100 - 返信
Yep, I found the same thing.
Finally got all the way down to this mother effer! :D
-
デバイスを再度組み立てるには、この説明書の逆の順番で組み立ててください。
デバイスを再度組み立てるには、この説明書の逆の順番で組み立ててください。
108 の人々がこのガイドを完成させました。
チーム
Cal Poly, Team 8-12, Regan Spring 2014 Cal Poly, Team 8-12, Regan Spring 2014人のメンバー
CPSU-REGAN-S14S8G12
5 メンバー
30のガイドは作成済み
15コメント
Great guide, but where to buy a fan for the ps4?!
Look one ebay, that's where my store gets the majority of out parts from. considering we fix computers.
Will this guide work with the CUH-1200 model?
My PS4 has been overheating so I decided to take it apart and clean it. I cleaned it well but it still over heats the fan will try to start up but cuts back off plz help
Replace the fan ... Yours works intermittently that probably means ut has a bad bearing.
Well, after replacing the fan, triple checking every thing and plugging it back in…. I got nothing. No power at all.
took it all apart three times to make sure all cables, connections and touch sensors were making contact. Still nothing.
With the bad fan in it at least still powered on befor this.
Many help appreciated !
My power button doesn’t work, but the eject works and the console seems to be running fine when I turn it on with my controller. Any ideas on what I did wrong?
This worked: https://youtu.be/L5Sp39M0O6Q
Megan -
I followed the guide with no issues, but when I hooked my ps4 up again and pressed the power button, the console beeped, I got the blue light, but then it turned off. No fan, no screen, nothing.
The power button works, and there is power - otherwise I wouldn’t get a beep.
So I took it apart and reinstalled the old noisy fan. When I put it back together, same result.
Anyone have any ideas what the problem could be?
Nice man. Very very so good your guide.
