はじめに

This guide shows you how to repair a disfunctional keyboard for the Palm Treo 680.

Remove the battery cover by pressing on the small rectangular button location the back of the phone.
  • Remove the battery cover by pressing on the small rectangular button location the back of the phone.

コメントを追加する

Remove the battery by pulling it out toward you.
  • Remove the battery by pulling it out toward you.

コメントを追加する

  • Unscrew the 0.266 inch top-left screw with a T6 Torx Screwdriver.

  • Be sure to remove the stylus in order to access the screw.

Use a T5 Torx screwdriver instead of a T6. T6 is too big.

Rhebakah Thomas - 返信

I found T5 too large as well. T4 seeems to work

Absent Minded Professor - 返信

  • Using the spudger, remove the rubber rectangular cover located in the upper right hand side of the device.

  • Unscrew the 0.266 inch screw with the T6 Torx Screwdriver.

    • If there is a red Palm sticker covering the screw, just puncture it to access the screw.

コメントを追加する

  • Remove the remaining two 0.266 inch screws at the bottom of the device.

コメントを追加する

  • Turn the phone 90 degrees to the right, so the screen is facing the right side.

  • Use a spudger to carefully separate the back panel from the front panel to access all the various components inside the phone.

  • Separate the covers from the left side of the device as indicated in the picture. The right side contains orange ribbons that are easily damaged.

コメントを追加する

  • Take the slim metal plate and slide it upwards, until it disconnects from the logic board.

  • DO NOT bend or crinkle this metal plate. It will be VERY DIFFICULT, IF NOT IMPOSSIBLE, to slide it back into place when you are re-assembling if you crinkle or bend this metal plate.

  • Set the metal plate aside for now.

コメントを追加する

  • Take the tweezers and locate the orange ribbon that connects the screen to the logic board.

  • There is a small piece of tape over the orange ribbon connector. Peal this off.

コメントを追加する

  • Slide the metal spundger between the orange ribbon and black connector. Flip the black connector upwards, releasing the orange ribbon.

  • Pull the orange ribbon away from the connector, in order to make sure wire is fully disconnected.

コメントを追加する

  • Now carefully turn the phone over so the screen is facing you.

  • Locate the other orange ribbon connecting the logic board to the face plate.

  • Take the spundger and slide it between the orange ribbon and tan connector. Life the tan connector up, releasing the orange ribbon.

  • Separate the logic board and face plate of the Palm Treo.

コメントを追加する

  • Ta Da! You now have the logic board separated from the phone! Here is what it should look like, on both sides.

コメントを追加する

  • Take the face plate of Treo, and locate the backside of it.

  • Unscrew the two screws on the back, using the T6 sized screwdriver.

コメントを追加する

  • Take off the plastic back panel, in order to gain access to the rubber keys of the keyboard.

  • Simply push on the keys and function bar(from the front of the Treo). They should pop right out.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Maiya123

メンバー登録日: 2009年10月22日

36 ポイント

12のガイドは作成済み

チーム

Cal Poly, Team 6-4, Maness Fall 2009 Cal Poly, Team 6-4, Maness Fall 2009人のメンバー

CPSU-MANESS-F09S6G4

4 メンバー

12のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 3

今までの合計 4,596