メインコンテンツにスキップ

はじめに

You will need a screw driver and prying tool for this guide. Some of the parts are hard to remove at first and have some force applied to them.

パーツ

パーツは指定されていません。

  1. The battery compartment cover is located on the top of the mouse. The seam running horizontally across the mouse is the top of the cover. There is a button to pop off the cover. It is located on the bottom of the mouse. you may need to press hard on this button to pop the cover. If the button does not work, you will need to pry off the cover. You can use your fingernails or a prying tool in order to do this, as seen in the third image.
    • The battery compartment cover is located on the top of the mouse. The seam running horizontally across the mouse is the top of the cover.

    • There is a button to pop off the cover. It is located on the bottom of the mouse. you may need to press hard on this button to pop the cover.

    • If the button does not work, you will need to pry off the cover. You can use your fingernails or a prying tool in order to do this, as seen in the third image.

  2. Remember to insert the new battery in the same orientation as the old one. The positive (plus) end should be facing away from the buttons.
    • Remember to insert the new battery in the same orientation as the old one. The positive (plus) end should be facing away from the buttons.

  3. The pads on the underside of the mouse hide the screws. Remove these first. You may need to use your fingernails or a prying tool. There will be two 0.5mm phillips head screws. Both will be underneath the bottom two pads.
    • The pads on the underside of the mouse hide the screws. Remove these first. You may need to use your fingernails or a prying tool.

    • There will be two 0.5mm phillips head screws. Both will be underneath the bottom two pads.

  4. Pry the top cover off. You may need to use a pry tool to help.
    • Pry the top cover off. You may need to use a pry tool to help.

  5. Use your fingernail to carefully remove the two skid stickers from the fat (non-button) end of the bottom of the mouse to reveal two Philips head screws. Remove these, then unclip the bottom cover. Don't get the sticky dusty. Now remove buttons; they're both attached by one 0.5mm Phillips head screw. It is located in the center of the top cover. Use your fingernail to carefully remove the two skid stickers from the fat (non-button) end of the bottom of the mouse to reveal two Philips head screws. Remove these, then unclip the bottom cover. Don't get the sticky dusty. Now remove buttons; they're both attached by one 0.5mm Phillips head screw. It is located in the center of the top cover.
    • Use your fingernail to carefully remove the two skid stickers from the fat (non-button) end of the bottom of the mouse to reveal two Philips head screws. Remove these, then unclip the bottom cover. Don't get the sticky dusty. Now remove buttons; they're both attached by one 0.5mm Phillips head screw. It is located in the center of the top cover.

  6. The button are now only attached by a small overhang near the front. You will need to use the pry tool to push the button plate off of this overhang as shown. The button plate should be able to be completely removed at this point.
    • The button are now only attached by a small overhang near the front. You will need to use the pry tool to push the button plate off of this overhang as shown.

    • The button plate should be able to be completely removed at this point.

終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Hannah Pate

メンバー登録日: 2015年01月30日

1,624 ポイント

7のガイドは作成済み

チーム

USF Tampa, Team 1-1, Watkins Winter 2015 USF Tampa, Team 1-1, Watkins Winter 2015人のメンバー

USFT-WATKINS-W15S1G1

4 メンバー

14のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 1

過去 7 日: 7

過去 30 日: 30

今までの合計 4,629