メインコンテンツにスキップ

修理を始めるには

修理する権利

ストア

はじめに

OWC’s Envoy Pro enclosures allow you to repurpose a factory-installed Mac SSD as a portable external drive. Follow this guide to learn how to install your SSD into the enclosure.

If you still need to complete your SSD upgrade, find your Mac starting from this page and look for the SSD Replacement guide.

Note: OWC Envoy Pro enclosures are designed for use with factory-installed Mac Solid State Drives, and will not work with other PCIe replacement drives and adapters, including OWC’s own Aura Pro drive.

  1. To open the enclosure, pull the top half down toward the wedged end and lift it away from the bottom half. To open the enclosure, pull the top half down toward the wedged end and lift it away from the bottom half. To open the enclosure, pull the top half down toward the wedged end and lift it away from the bottom half.
    • To open the enclosure, pull the top half down toward the wedged end and lift it away from the bottom half.

  2. Carefully insert your Mac OEM SSD as shown at left, with the golden contact pads below the connector pins facing upward. The SSD might take a significant amount of force to insert. Make sure you have the orientation correct before you apply any pressure. When the SSD is fully inserted, you should barely be able to see the golden contact points at the top of the drive, and the notch at the bottom of the drive should be aligned with the hole for the screw in the enclosure.
    • Carefully insert your Mac OEM SSD as shown at left, with the golden contact pads below the connector pins facing upward.

    • The SSD might take a significant amount of force to insert. Make sure you have the orientation correct before you apply any pressure.

    • When the SSD is fully inserted, you should barely be able to see the golden contact points at the top of the drive, and the notch at the bottom of the drive should be aligned with the hole for the screw in the enclosure.

  3. Use a T5 Torx driver to install the 6.5 mm screw securing the bottom of the SSD.
    • Use a T5 Torx driver to install the 6.5 mm screw securing the bottom of the SSD.

  4. 電源プラグから解放されて、好きな場所で勉強する。

    Mac用バッテリー修正キット

    修理キットを探す

    電源プラグから解放されて、好きな場所で勉強する。

    Mac用バッテリー修正キット

    修理キットを探す
  5. Reinstall the top half of the enclosure and slide it closed. Reinstall the top half of the enclosure and slide it closed. Reinstall the top half of the enclosure and slide it closed.
    • Reinstall the top half of the enclosure and slide it closed.

  6. Use a T5 Torx driver to install the two 7.6 mm screws on the bottom of the enclosure.
    • Use a T5 Torx driver to install the two 7.6 mm screws on the bottom of the enclosure.

  7. Remove the backing from the adhesive on the extra rubber foot provided in the plastic bag with the screws. With the backing removed, place the sticky side of the rubber foot down over the screws you just inserted, and apply pressure to it for 30 seconds. With the backing removed, place the sticky side of the rubber foot down over the screws you just inserted, and apply pressure to it for 30 seconds.
    • Remove the backing from the adhesive on the extra rubber foot provided in the plastic bag with the screws.

    • With the backing removed, place the sticky side of the rubber foot down over the screws you just inserted, and apply pressure to it for 30 seconds.

  8. The drive is now ready to be connected to your computer with the included USB cable.
    • The drive is now ready to be connected to your computer with the included USB cable.

終わりに

Once your drive is installed, you can transfer data from it, or use Disk Utility to format it and use it as a Time Machine backup.

7 の人々がこのガイドを完成させました。

Taylor Dixon

メンバー登録日: 2018年06月26日

35,605 ポイント

87のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

130 メンバー

12,408のガイドは作成済み

2 件のコメント

Does anyone know why the OWC Envoy Pro enclosure DOES NOT work with the OWC’s Aura Pro drive? I have noticed the warning (included above as well) that the enclosure only works with “factory-installed Mac Solid State Drives”. One would think that if the OWC Aura Pro drive can serve as a replacement for a Mac SSD that it should work in the Envoy Pro enclosure as well. The reason that I ask is that it would be much easier to format and transfer data to the Aura Pro drive via the enclosure rather than having to do this all after installation in the Mac computer.

markbrandon - 返信

I have OWC 480Gb SSD for MacBookAir mid 2012. I called OWC to ask the same question. I was told that it actually was a Heat matter, that it would work but at my own risk. I feel I was lucky to get that response and that they probably do not give it any more. I tried it with success, keeping the Enclosure lid open. I would not use it extensively though. For extra safety you can always use a small fan to cool it up. I think you can respect their recommandations by booting from the external enclosure with the original Mac SSD in it and then Clone it to the internal freshly formatted OWC SSD. I now have another OWC 480Gb SSD for MacBookAir 2015. Am I going to have the guts to also give it a try ? Just to play safe I will try not to. So I would suggest that a Heat Monitoring Program be installed and that both Original Apple and OWC SSD Temperature be monitored and compared.

Midu - 返信

コメントを追加

統計データを表示:

過去 24時間: 14

過去 7 日: 70

過去 30 日: 315

今までの合計 5,571