メインコンテンツにスキップ

はじめに

You've had a terrible accident and realized that your GoPro has a crack right through the center of the lens! Use our guide to resurrect you GoPro back to life!

  1. Push the tab on the back of the device left to remove the plate covering the battery. Push the tab on the back of the device left to remove the plate covering the battery.
    • Push the tab on the back of the device left to remove the plate covering the battery.

  2. Use the strip of tape on the battery to remove the battery from the housing.
    • Use the strip of tape on the battery to remove the battery from the housing.

  3. Insert a plastic opening tool in between the front face plate and the black housing.
    • Insert a plastic opening tool in between the front face plate and the black housing.

    • Make sure you insert the plastic opening tool next to the microSD card slot. There is a small gap that will help separate the face plate.

  4. Continue to use the plastic opening tool and separate the front face plate from the rest of the device.
    • Continue to use the plastic opening tool and separate the front face plate from the rest of the device.

    • There is adhesive that helps attach the front face plate. Some extra prying may be required to separate the face plate, but do not use excessive force.

  5. Locate the four 8.1mm PH00 screws on the corners of the GoPro and unscrew them using the phillips screwdriver. Gently remove the motherboard by using a plastic opening tool to pry it out of the housing. Be careful not to damage the ribbon cable connected to the GoPro housing and motherboard.
    • Locate the four 8.1mm PH00 screws on the corners of the GoPro and unscrew them using the phillips screwdriver.

    • Gently remove the motherboard by using a plastic opening tool to pry it out of the housing.

    • Be careful not to damage the ribbon cable connected to the GoPro housing and motherboard.

  6. Android 修理キット

    A new screen or battery is one kit away.

    ショップを見る

    Android 修理キット

    A new screen or battery is one kit away.

    ショップを見る
  7. Remove the ribbon cable by carefully flipping the black clip up with the plastic opening tool and pulling the cable out. Remove the ribbon cable by carefully flipping the black clip up with the plastic opening tool and pulling the cable out.
    • Remove the ribbon cable by carefully flipping the black clip up with the plastic opening tool and pulling the cable out.

  8. Remove the four 4mm PH00 screws attaching the image sensor to the motherboard with your screwdriver.
    • Remove the four 4mm PH00 screws attaching the image sensor to the motherboard with your screwdriver.

  9. Pry off the last ribbon cable with a plastic opening tool. Remove the image sensor from the motherboard.
    • Pry off the last ribbon cable with a plastic opening tool.

    • Remove the image sensor from the motherboard.

  10. Using your screwdriver, unscrew three 4mm PH00 screws that will free the metal plate.
    • Using your screwdriver, unscrew three 4mm PH00 screws that will free the metal plate.

    • A small plate will become separated when the rightmost screw is removed. Just place it to the side.

  11. Use the plastic opening tool to pry off the referenced ribbon cable from the motherboard. The microSD and Accessory Board is now ready for removal.
    • Use the plastic opening tool to pry off the referenced ribbon cable from the motherboard.

    • The microSD and Accessory Board is now ready for removal.

  12. Remove the single 3.2mm PH00 screw with your screwdriver to detach the motherboard from the mid frame.
    • Remove the single 3.2mm PH00 screw with your screwdriver to detach the motherboard from the mid frame.

  13. Use a plastic opening tool to gently separate the LCD ribbon cable from the motherboard. Gently remove the motherboard from the midframe using tweezers. Remove motherboard by lifting from the edges. This will reduce the chance of damaging components on the motherboard.
    • Use a plastic opening tool to gently separate the LCD ribbon cable from the motherboard.

    • Gently remove the motherboard from the midframe using tweezers.

    • Remove motherboard by lifting from the edges. This will reduce the chance of damaging components on the motherboard.

  14. Use your PH00 screwdriver to remove the last three screws from the mid frame. This will release the lens housing from the mid frame.
    • Use your PH00 screwdriver to remove the last three screws from the mid frame. This will release the lens housing from the mid frame.

  15. Carefully remove the lens from the font housing.
    • Carefully remove the lens from the font housing.

まとめ

To reassemble your device, follow these instructions in reverse order.

8 の人々がこのガイドを完成させました。

Patrick Cook

メンバー登録日: 2015年10月01日

663 ポイント

3のガイドは作成済み

チーム

Cal Poly, Team 5-8, Maness Fall 2015 Cal Poly, Team 5-8, Maness Fall 2015人のメンバー

CPSU-MANESS-F15S5G8

4 メンバー

6のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 12

今までの合計 1,761