修理を始めるには コミュニティ ストア

GameStop GS3 GameCube Controller Buttons Replacement

はじめに

After many hours of use, the buttons on the Gamecube Controller can become too loose or stick. This guide will provide instructions on how to replace the buttons of the GameStop GS3 Gamecube Controller. There are ten total buttons in this controller: left and right triggers, Z, turbo, D-pad, start/pause, A, B, X, and Y.

必要な工具と部品

  1. GameStop GS3 GameCube Controller Buttons Replacement, Back Panel: 手順 1、 3の画像 1 GameStop GS3 GameCube Controller Buttons Replacement, Back Panel: 手順 1、 3の画像 2 GameStop GS3 GameCube Controller Buttons Replacement, Back Panel: 手順 1、 3の画像 3

    • First, remove the 6 screws in the back panel and pull the back panel off.

    • Separate the halves of the controller. However, be careful when separating due to the little wires that could get mixed up.

    編集

  2. GameStop GS3 GameCube Controller Buttons Replacement: 手順 2、 3の画像 1 GameStop GS3 GameCube Controller Buttons Replacement: 手順 2、 3の画像 2 GameStop GS3 GameCube Controller Buttons Replacement: 手順 2、 3の画像 3

    • Next, remove the rumble motor by unscrewing the 2 screws connecting it.

    編集

  3. GameStop GS3 GameCube Controller Buttons Replacement: 手順 3、 3の画像 1 GameStop GS3 GameCube Controller Buttons Replacement: 手順 3、 3の画像 2 GameStop GS3 GameCube Controller Buttons Replacement: 手順 3、 3の画像 3

    • Finally remove the screws holding in the right and left triggers. It's easiest to hold the trigger together as shown in the third picture. Remove both the left and right trigger, and then you have successfully removed your back panel.

    編集

  5. GameStop GS3 GameCube Controller Buttons Replacement, Buttons: 手順 4、 1の画像 1

    • Hold the controller as shown in the picture so that you can remove the circuit board.

    • The locations of screws to be removed in future steps are shown in red.

    編集

  6. GameStop GS3 GameCube Controller Buttons Replacement: 手順 5、 2の画像 1 GameStop GS3 GameCube Controller Buttons Replacement: 手順 5、 2の画像 2

    • Now that the back panel has been removed it should be easy to snap off the "Z" and "TURBO" buttons as shown in the images.

    編集

  7. GameStop GS3 GameCube Controller Buttons Replacement: 手順 6、 1の画像 1

    • Remove the two screws on the motherboard so that you can remove the motherboard from the front cover.

    編集

  8. GameStop GS3 GameCube Controller Buttons Replacement: 手順 7、 1の画像 1

    • Now your controller front panel should look similar to this.

    • Remove the rubber backings on the buttons shown in red.

    • Snap them back in when you go to put the controller back together.

    編集

  9. GameStop GS3 GameCube Controller Buttons Replacement: 手順 8、 1の画像 1

    • Remove the buttons and you should have what you see here.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

11人の作成者と共同で作成されました。

Andrew Gonsalves

メンバー登録日: 10/20/16

226 ポイント

2のガイドは作成済み

バッジ: 9

+6 個以上のバッジ

チーム

UMass Dartmouth, Team 3-5, Isaacson Fall 2016 UMass Dartmouth, Team 3-5, Isaacson Fall 2016人のメンバー

UMASSD-ISAACSON-F16S3G5

3 メンバー

10のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 1

過去 7 日: 5

過去 30 日: 12

今までの合計 847