パーツ

パーツは必要ありません。

Remove the battery (which also functions as the back cover) from the device. This step is not explicitly shown, but a picture without the battery cover shows the device post-battery removal. Remove the battery (which also functions as the back cover) from the device. This step is not explicitly shown, but a picture without the battery cover shows the device post-battery removal.
  • Remove the battery (which also functions as the back cover) from the device. This step is not explicitly shown, but a picture without the battery cover shows the device post-battery removal.

コメントを追加する

Use a Philip's head screw driver to remove the screws from the case. Place the screws in a small container to avoid losing them.
  • Use a Philip's head screw driver to remove the screws from the case.

  • Place the screws in a small container to avoid losing them.

コメントを追加する

Remove the front cover. First, insert a small pry bar where the black front cover and white back cover meet. Begin prying the black plastic up, slowing moving around to the bottom and other side.
  • Remove the front cover.

    • First, insert a small pry bar where the black front cover and white back cover meet.

    • Begin prying the black plastic up, slowing moving around to the bottom and other side.

    • At an angle, carefully pull up on the front cover separate the two pieces.

  • Excellent! Now you have removed the front cover!

コメントを追加する

While looking down at the device, place your index finger at the top of the circuit board and your thumb on the device screen.
  • While looking down at the device, place your index finger at the top of the circuit board and your thumb on the device screen.

コメントを追加する

Using your fingers, gently pull the top of the circuit board up toward you while also sliding the bottom of the circuit board away from the bottom of the Sirius Stiletto 100 back cover. Using your fingers, gently pull the top of the circuit board up toward you while also sliding the bottom of the circuit board away from the bottom of the Sirius Stiletto 100 back cover.
  • Using your fingers, gently pull the top of the circuit board up toward you while also sliding the bottom of the circuit board away from the bottom of the Sirius Stiletto 100 back cover.

コメントを追加する

Congratulations! You have successfully removed the internal circuit board from the Sirius Stiletto 100 back cover.
  • Congratulations! You have successfully removed the internal circuit board from the Sirius Stiletto 100 back cover.

コメントを追加する

Flip the circuit board over to look at the back side, so that LCD screen is facing away from you. Use a Phillip's head screwdriver to remove the screw from the back of the internal antenna. Use a Phillip's head screwdriver to remove the screw from the back of the internal antenna.
  • Flip the circuit board over to look at the back side, so that LCD screen is facing away from you.

  • Use a Phillip's head screwdriver to remove the screw from the back of the internal antenna.

コメントを追加する

Use your fingers to pry the internal antenna off of the circuit board. You may need to wiggle it back and forth to successfully remove it. Woohoo! You have removed the internal antenna!
  • Use your fingers to pry the internal antenna off of the circuit board. You may need to wiggle it back and forth to successfully remove it.

  • Woohoo! You have removed the internal antenna!

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Trey

メンバー登録日: 2012年03月09日

77 ポイント

2のガイドは作成済み

チーム

Clemson, Team 2-1, Benson Spring 2012 Clemson, Team 2-1, Benson Spring 2012人のメンバー

CLEM-BENSON-S12S2G1

3 メンバー

6のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 4

過去 30 日: 6

今までの合計 2,531