はじめに

This is a step-by-step guide showing how to remove the LCD/Digitizer combo from the IBM WorkPad c3. This is a fairly easy removal.

パーツ

パーツは必要ありません。

Turn the device over so that the screen is facing down. In the next step the device will be heated, so the screen must be turned over to prevent heat damage to the LCD/Digitizer.
  • Turn the device over so that the screen is facing down.

  • In the next step the device will be heated, so the screen must be turned over to prevent heat damage to the LCD/Digitizer.

コメントを追加する

Using a hair dryer, slowly heat the edges of the WorkPad.
  • Using a hair dryer, slowly heat the edges of the WorkPad.

  • Spend at least one minute heating each side of the device. This will melt the glue holding the case together, and allow it to be removed.

  • Be sure not to touch the device directly after heating as it will be extremely hot. Use a towel or oven mitt to grab it.

コメントを追加する

Use a plastic opening tool to pry the back case from the WorkPad. If the rear cover is not coming off very easily, you probably need to reheat the case in order to sufficiently melt the glue.
  • Use a plastic opening tool to pry the back case from the WorkPad.

  • If the rear cover is not coming off very easily, you probably need to reheat the case in order to sufficiently melt the glue.

コメントを追加する

Turn the device over, so that the screen is laying on a flat surface. Turn the device over, so that the screen is laying on a flat surface.
  • Turn the device over, so that the screen is laying on a flat surface.

コメントを追加する

If the back case has already been removed, carefully place it on the WorkPad to protect the circuitry inside from the heat. Using the hair dryer, slowly heat the edges of the device. Spend at least 1 minute on each side, thoroughly heating the case. The LCD/Digitizer combo is very sensitive to heat, and can easily be ruined if it is directly exposed to the hair dryer. Verify that the screen is face down.
  • If the back case has already been removed, carefully place it on the WorkPad to protect the circuitry inside from the heat.

  • Using the hair dryer, slowly heat the edges of the device. Spend at least 1 minute on each side, thoroughly heating the case.

  • The LCD/Digitizer combo is very sensitive to heat, and can easily be ruined if it is directly exposed to the hair dryer. Verify that the screen is face down.

コメントを追加する

The device will be extremely hot. Use a towel or oven mitt to grab it. Using the Plastic Opening Tools, take the front of the case off.
  • The device will be extremely hot. Use a towel or oven mitt to grab it.

  • Using the Plastic Opening Tools, take the front of the case off.

  • If the case is difficult to remove, try repeating step 2.

  • The power button at the top of the device will be loose once the front part of the case is removed.

コメントを追加する

Remove the yellow tape that is covering the battery connector
  • Remove the yellow tape that is covering the battery connector

コメントを追加する

Using the tweezers, carefully disconnect the battery cable from the port
  • Using the tweezers, carefully disconnect the battery cable from the port

コメントを追加する

Using the plastic opening tools, lift the battery out of the case The battery is secured with adhesive and it will take some effort to remove
  • Using the plastic opening tools, lift the battery out of the case

  • The battery is secured with adhesive and it will take some effort to remove

コメントを追加する

Using the spudger lift the tabs  holding the LCD/Digitizer combo cables to the WorkPad. Using the spudger lift the tabs  holding the LCD/Digitizer combo cables to the WorkPad.
  • Using the spudger lift the tabs holding the LCD/Digitizer combo cables to the WorkPad.

コメントを追加する

Using your thumb, press down gently on the back of the LCD. The LCD will disconnect and fall out of the case, so be sure to have your hand waiting for it.
  • Using your thumb, press down gently on the back of the LCD.

  • The LCD will disconnect and fall out of the case, so be sure to have your hand waiting for it.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

Emily Falkenstein

メンバー登録日: 2010年10月05日

51 ポイント

5のガイドは作成済み

チーム

Cal Poly, Team 21-35, Regan Fall 2010 Cal Poly, Team 21-35, Regan Fall 2010人のメンバー

CPSU-REGAN-F10S21G35

3 メンバー

5のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 1,439