はじめに

Removing the buttons might be necessary if a button is damaged. This guide will show how to remove all external buttons on the camera.

パーツ

パーツは必要ありません。

The camera used to create these repair guides had a broken lens assembly.  As a result, the lens is sticking out in all of the photos, but it is important to note that this should not be the case with your camera.  The lens should retract itself back into the camera when it is turned off. Use your fingernail to slide the dark gray tab located on the bottom of the device towards the edge of camera. Slide the light gray door away from the LCD screen and pull up to open the door.
  • The camera used to create these repair guides had a broken lens assembly. As a result, the lens is sticking out in all of the photos, but it is important to note that this should not be the case with your camera. The lens should retract itself back into the camera when it is turned off.

  • Use your fingernail to slide the dark gray tab located on the bottom of the device towards the edge of camera.

  • Slide the light gray door away from the LCD screen and pull up to open the door.

  • Both battery and memory card should now be visible.

コメントを追加する

Rotate the small brown tab towards the edge of the camera. The battery should pop up.
  • Rotate the small brown tab towards the edge of the camera.

  • The battery should pop up.

コメントを追加する

Pull the battery straight out of the battery holder.
  • Pull the battery straight out of the battery holder.

  • When putting the battery back in, make sure it is orientated the same as it was before.

コメントを追加する

Close light gray battery compartment door. Remove the six 2.8 mm Phillips screws on the outside of the case. Two screws are found on each side of the camera, and the final two are found on the bottom. Remove the six 2.8 mm Phillips screws on the outside of the case. Two screws are found on each side of the camera, and the final two are found on the bottom.
  • Close light gray battery compartment door.

  • Remove the six 2.8 mm Phillips screws on the outside of the case. Two screws are found on each side of the camera, and the final two are found on the bottom.

コメントを追加する

Use your fingers to carefully pry off the back casing from the camera assembly. Casing should lift straight off. Use your fingers to carefully pry off the back casing from the camera assembly. Casing should lift straight off.
  • Use your fingers to carefully pry off the back casing from the camera assembly. Casing should lift straight off.

コメントを追加する

Push the buttons out with your finger if they did not fall out while removing the casing. Pull off the white plastic side piece if it did not fall out while removing the casing. Pull off the white plastic side piece if it did not fall out while removing the casing.
  • Push the buttons out with your finger if they did not fall out while removing the casing.

  • Pull off the white plastic side piece if it did not fall out while removing the casing.

コメントを追加する

Remove the one 2.2 mm Phillips screw from the bottom of the camera. Take off the print button.
  • Remove the one 2.2 mm Phillips screw from the bottom of the camera.

  • Take off the print button.

コメントを追加する

Use your fingers to carefully pry off the front casing of the camera. The front casing should pull straight off. Use your fingers to carefully pry off the front casing of the camera. The front casing should pull straight off.
  • Use your fingers to carefully pry off the front casing of the camera. The front casing should pull straight off.

コメントを追加する

Use the flat end of the spudger to lift open the white plastic latch on the front of the camera. Once the latch is lifted up, move the latch up towards the top edge of the camera. Remove the top button assembly by pulling straight up.
  • Use the flat end of the spudger to lift open the white plastic latch on the front of the camera. Once the latch is lifted up, move the latch up towards the top edge of the camera.

  • Remove the top button assembly by pulling straight up.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

James Loy

メンバー登録日: 2010年10月06日

103 ポイント

7のガイドは作成済み

チーム

Cal Poly, Team 5-12, Maness Fall 2010 Cal Poly, Team 5-12, Maness Fall 2010人のメンバー

CPSU-MANESS-F10S5G12

4 メンバー

7のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 2

今までの合計 1,287