修理を始めるには

修理する権利

ストア

Astro A40 TR Speakers Replacement

作成者： Bhargav Makkapati (そして 2 人のその他投稿者)
  • コメント: 2
  • お気に入り: 0
  • 完了: 1

難易度

簡単

手順

5

所要時間

15 - 20 分

セクション

1

フラグ

1

Better Introduction

より良い紹介部分

この紹介部分を完成し編集することでこのガイドを改良する

ツール

これらのツールを購入する

パーツ

パーツは指定されていません。

  1. To access the speakers you need to disassemble the earpiece. First remove the foam ear piece by simply pinching the padding and pulling lightly until the magnets disengage. To access the speakers you need to disassemble the earpiece. First remove the foam ear piece by simply pinching the padding and pulling lightly until the magnets disengage.

    • To access the speakers you need to disassemble the earpiece. First remove the foam ear piece by simply pinching the padding and pulling lightly until the magnets disengage.

    翻訳

  2. Remove the dust cover located on the speaker. Use the corner of the spudger to peel underneath the cover until you can lift it by hand. The cover is held onto the device with adhesive and should be removed slowly. Remove the dust cover located on the speaker. Use the corner of the spudger to peel underneath the cover until you can lift it by hand. The cover is held onto the device with adhesive and should be removed slowly. Remove the dust cover located on the speaker. Use the corner of the spudger to peel underneath the cover until you can lift it by hand. The cover is held onto the device with adhesive and should be removed slowly.

    • Remove the dust cover located on the speaker. Use the corner of the spudger to peel underneath the cover until you can lift it by hand. The cover is held onto the device with adhesive and should be removed slowly.

    翻訳

  3. The Essential Toolkit

    コンパクト版iFixitキットの中で最も利便性の高いツール

    ショップを見る

    The Essential Toolkit

    コンパクト版iFixitキットの中で最も利便性の高いツール

    ショップを見る

  4. Take off the front cover by removing the four screws located in a square formation on the surface of the device. Use the J00 Philips driver listed in the device page. Take off the front cover by removing the four screws located in a square formation on the surface of the device. Use the J00 Philips driver listed in the device page.

    • Take off the front cover by removing the four screws located in a square formation on the surface of the device. Use the J00 Philips driver listed in the device page.

    翻訳

  5. Locate the three small screws under the speaker. Use the J00 Philips Driver to remove them. Locate the three small screws under the speaker. Use the J00 Philips Driver to remove them.

    • Locate the three small screws under the speaker. Use the J00 Philips Driver to remove them.

    翻訳

  6. If your issue is asking for the complete replacement of the speaker or the motherboard, un-solder the old components and replace with new speaker by re-soldering.

    • If your issue is asking for the complete replacement of the speaker or the motherboard, un-solder the old components and replace with new speaker by re-soldering.

    • Check out this useful guide on how to solder and desolder connections if soldering is new to you.

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

2他の投稿者と一緒に

Bhargav Makkapati

メンバー登録日: 2016年10月20日

156 ポイント

1ガイドが承認済み

バッジ: 8

+5 個以上のバッジ

チーム

UMass Dartmouth, Team 6-5, Martin Fall 2016 UMass Dartmouth, Team 6-5, Martin Fall 2016人のメンバー

UMASSD-MARTIN-F16S6G5

3 メンバー

5のガイドは作成済み

コメント1件

コメントを追加

I’ve found potential replacement speakers here. They look fairly similar to the ones in the A40s, but the resistance value marked on the speakers in the guide vs on the listing is different.

Buyer caution must be taken before actually making the plunge, as sound quality might be different. The listing is from Ali Express after all.

Adrian Kennedy - 返信

コメントを追加

統計データを表示:

過去 24時間: 10

過去 7 日: 38

過去 30 日: 163

今までの合計 4,795