Required temperature to remove the screen bezel?

Question

MacBook Air 13インチ Early 2015

2015年3月のアップデートではアップルの13インチMacBook Airは第5世代Intel Core i5またはi7プロセッサーを特徴としており、これによりわずかな性能とバッテリーライフの向上がされました。

634回答すべてを表示

livfe @livfe

評価: 687

7

1

投稿日: 2024年6月18日

オプション

Required temperature to remove the screen bezel?

I have a general question for all models of MB Air 2010 - 2017

I need to replace some internal cables & hinges but need to know how hot must I set the heat gun to soften the adhesive enough for removal?

And is it possible to replace the Antenna / Wifi cable, can't find any guide on this.... I broke the wire off from the connector on the wifi cable and soldering it back looks like a seriously tricky job https://www.youtube.com/watch?v=UnNCSlU4...

回答がありました！ 回答を表示同じ問題があります

この質問は役に立ちましたか？

はいいいえ

スコア 1

コメントを追加

1 件の回答

ベストアンサー

Dan @danj

評価: 482千

Self employed contract worker

35

332

971

投稿日: 2024年6月18日

オプション

Here’s a good vid on the process MacBook Air LCD repair, how to replace LCD only as far as the heat it doesn’t take much I set my heat gun to 125 Fahrenheit and as seen in the vid holding the air stream over the bezel and away from the rubber edge.

このアンサーは役に立ちましたか？

はいいいえ

スコア 0

3 件のコメント:

Yes seen that, seen the guides in here, I also have a 2009 MBP (The stage lights) that I finally have got a new cable for... the screen is proper stubborn and won't budge a mm even at 150 degrees... IF I go higher I will destroy everything... been heating areas for 20 minutes.... none of them seem to want to budge.

livfe さんによる2024年6月23日

@livfe - are you using a suction cup to help in lifting? I’ve hit a few hard one’s because someone glued the glass down with the wrong adhesive material or just too much.

Focus on one corner and after you lift it use a playing card to hold it free (if needed cut the card in half or even smaller). Then walk the edge, you may need to raise the temp a bit and even then it can be very difficult because of previous repairs.

Dan さんによる2024年6月23日

@danj Dan, I know how to get them out, I seen 10 videos on it, It didn't look like anyone was in ther before me, glue was sold. Anyway, screen shattered, and scraping out the residue was a task but now it is clean of everything and the new screen is in, just got to source a new glass.... and the correct longer cable.

The suction cup didn't get into play the glass smashed after I got the 2nd thin plastic tool under it. Glue was sold.

livfe さんによる2024年6月23日

コメントを追加

Yes seen that, seen the guides in here, I also have a 2009 MBP (The stage lights) that I finally have got a new cable for... the screen is proper stubborn and won't budge a mm even at 150 degrees... IF I go higher I will destroy everything... been heating areas for 20 minutes.... none of them seem to want to budge. — livfe
@livfe - are you using a suction cup to help in lifting? I’ve hit a few hard one’s because someone glued the glass down with the wrong adhesive material or just too much.

Focus on one corner and after you lift it use a playing card to hold it free (if needed cut the card in half or even smaller). Then walk the edge, you may need to raise the temp a bit and even then it can be very difficult because of previous repairs. — Dan
@danj Dan, I know how to get them out, I seen 10 videos on it, It didn't look like anyone was in ther before me, glue was sold. Anyway, screen shattered, and scraping out the residue was a task but now it is clean of everything and the new screen is in, just got to source a new glass.... and the correct longer cable.

The suction cup didn't get into play the glass smashed after I got the 2nd thin plastic tool under it. Glue was sold. — livfe

MacBook Air 13インチ Early 2015

Required temperature to remove the screen bezel?

1 件の回答

回答を追加する