メインコンテンツにスキップ

Repair guides and troubleshooting for the Whirlpool Quiet Partner II insulated dishwasher.

38回答 すべてを表示

How do I reset my Quite Partner II Dishwasher

My Quiet Partner II dishwasher is not working - the control panel is no longer lit up. I am having a difficult time trying to find out how to Reset it with the correct control panel button sequence for this model. I believe it is hard-wired so I have checked the breakers in my basement. I have pushed some buttons and the lights came on and off but not working. and When I push the cancel button it comes on -:O) instead of the start button and the washing selections. Help! :O)

この質問に回答する 同じ問題があります

この質問は役に立ちましたか?

スコア 0
3 件のコメント

Hi,

What is the model number of the dishwasher?

さんによる

Model #Du1055xtvq8

さんによる

Hi @stihl209

Did you try the Most Helpful Answer below, you didn't say?

さんによる

コメントを追加

5件の回答

最も参考になった回答

Judy Doughty some of this will depend on your DW exact model. In general to reset the Quiet Partner II you:

Open the DW door

Push "heated dry," "normal," "heated dry" and "normal" in quick succession. immediately after this close the dishwasher door.

このアンサーは役に立ちましたか?

スコア 5

10 件のコメント:

Thank you it worked. Dishwasher is up and running. DT

さんによる

@daybreak1964 good job and thanks for letting us know!

さんによる

It didnt work for me .. Any other ideas ?? Please

さんによる

@Wanda Reddick

What is the model number of the dishwasher?

さんによる

I had success with pressing both buttons at the same time, twice. Then closing the door. I may have even closed the door as I was pushing the buttons for the 2nd time.

さんによる

5件以上のコメントを表示

コメントを追加

I had success with pressing both buttons at the same time, twice. Then closing the door. I may have even closed the door as I was pushing the buttons for the 2nd time.

このアンサーは役に立ちましたか?

スコア 0

1件のコメント:

I have a whirlpool gold DW model # GU1500XTKT0 not operating and have a constant flashing rinse only light. Any ideas that I may try?

さんによる

コメントを追加

Normal wash, light wash and off/reset lights are flashing at same time. No other buttons will work.

このアンサーは役に立ちましたか?

スコア 0

2 件のコメント:

This worked for me as well! Thank you!

さんによる

Same issue here! I turned the breaker off and pulled the chipboard out unplugging it completely, put it all back together and it worked just fine!

さんによる

コメントを追加

My dishwasher is flashing on the normal wash and will not come on

このアンサーは役に立ちましたか?

スコア 0

2 件のコメント:

Same issue here! I turned the breaker off and pulled the chipboard out unplugging it completely, put it all back together and it worked just fine! Sometimes just turning the breaker off for 30 seconds will reset it.

さんによる

I posted same issue above but now see you have dealt with this already. Is the CPU board behind the inside door panel? Removing i think 14 screws will allow me access?

さんによる

コメントを追加

I’m just getting all lights on with no response to any button being pushed after doing the heated dry/normal push reset. Any ideas what could be going on?

このアンサーは役に立ちましたか?

スコア 0

1件のコメント:

Hi,

What is the model number of the dishwasher?

Have you tried disconnecting the power to the dishwasher for 5 minutes and checked if that reset it?

さんによる

コメントを追加

回答を追加する

Judy Doughty さん、ありがとうございました!
統計データ:

過去 24時間: 27

過去 7 日: 229

過去 30 日: 1,052

今までの合計 15,236