メインコンテンツにスキップ

2017年11月4日に発売。モデル番号はA1865, A1901です。GSMか CDMA / 64か256 GB/カラーはシルバーかスペースグレー

1028回答 すべてを表示

Face ID not working after Earpiece Speaker/Sensor Assembly replacement

Hi all,

I had my iPhone X ear piece speaker stop working the other day. I bought a replacement Earpiece Speaker and Sensor Assembly for my model phone off of ifixit, and just replaced it today. After swapping it, turning the phone on, I got the message pop up saying “Unavailable to activate face ID on this phone”. I then go into my face ID settings, attempt to set it up, but then get the message “Face ID is not available, try setting up face ID later”. The ear speaker is now working fine, but face ID is not. I opened it back up, verified all the connections are good, re-seated all of them, checked the sensors, made sure they were all clean, no prints or dirt, but still no luck. Could the replacement I got have a bad sensor? Anybody have any other suggestions at all?

Thanks!

この質問に回答する 同じ問題があります

この質問は役に立ちましたか?

スコア 3
コメントを追加

5件の回答

最も参考になった回答

The Face ID and earpiece assembly is paired to each iPhone, if replaced it will never work again. You need the original one from the original screen transferred over to the new display, then it will work again. If the original one is damaged, then you just have to live without that feature.

このアンサーは役に立ちましたか?

スコア 1
コメントを追加

@skunkape … typically on any repair that involves removing the screen and accessing the internals, the cause of any new issue that arises after is typically caused by the individual doing the repair. that being said, and being that you have retraced your steps and reseated everything, i would look for damaged flex cables and or connectors. here is a guide specifically for this new issue:

How to Fix iPhone X Face ID Not Available

このアンサーは役に立ちましたか?

スコア 0
コメントを追加

@jostewcrew, thanks for the tips. Even though it was brand new, I did check over the flex cables, and didn’t see any rips or tears on any of them, but I didn’t inspect the connectors. I’ll double check those when I get a chance and see if those seem to have any issue.

このアンサーは役に立ちましたか?

スコア 0

コメント:

ok...best of luck. also, when inspecting flex connectors, visible tears and rips arent always the case. would want to be thourough as possible by holding up to a light and using a magnifier for any line breaks.

さんによる

コメントを追加

I believe when you do a ear speaker replacement Face ID is no longer available. As the original apple ear piece has coding that others don’t have. I’m having this issue myself and hope this helped. Also if anyone has tips I’m desperate.

このアンサーは役に立ちましたか?

スコア 0

コメント:

The speaker isn’t paired to the device, the flood illuminator is what’s paired.. I carry out this repair without loosing faceID.. as long as the flex cable is in good condition I desolder the original speaker and solder the replacement on to the original flex. Bringing life back to the earpiece and retaining faceID.. I wouldn’t recommend you trying this technique as the solder points are microscopic, if you know of any repair shops that specialise in micro soldering it should be a walk on the park for them

さんによる

So the black part on the right side that has metal bumps on it should be soldered to the part under it to fix the issue? My step dad knows how to solder if that’s the case.

さんによる

コメントを追加

The Face ID and earpiece assembly is paired to each iPhone, if replaced it will never work again. You need the original one from the original screen transferred over to the new display, then it will work again. If the original one is damaged, then you just have to live without that feature

found that on the internet

このアンサーは役に立ちましたか?

スコア 0

コメント:

Matt above has the correct answer. The flood illuminator that is part of the ear speaker ribbon cable assembly is the part that is “paired” to the motherboard such that only Apple can currently fit a new assembly and pair it but they don’t offer this as a normal (priced repair)!

This may change with Apples recent announcement on relatability but until they release a method to pair a new flood illuminator to an existing motherboard micro soldering a new speaker to your old cable with flood illuminator is the only option that retains FaceID

Have the same low volume on my IPhone X so currently just use it in speakerphone mode for now!

さんによる

コメントを追加

回答を追加する

Aaron さん、ありがとうございました!
統計データを表示:

過去 24時間: 20

過去 7 日: 143

過去 30 日: 682

今までの合計 9,005