修理を始めるには コミュニティ ストア

Appleはスリムダウンして性能を上げたiPad Airを2013年11月1日に発売しました。スペースグレーとシルバーの2色から選べます。カスタムA7 プロセッサー搭載しており、容量は16、32、64と128 GBがあります。

577回答 すべてを表示

オプション

iPad Air 1 not charging after replacing digitizer.

I replaced the digitizer on an iPad Air 1. The iPad shows that it is charging and the tone is heard when plugged in, still it does not charge above 40%. I am using an official charger and cable that works on another iPad. This is not the first digitizer that I have replaced. I have reset and downloaded the most current iSO. I followed the ifixit instructions. I am at end on what to try next. Any help will be greatly appreciated.

回答がありました！ 回答を表示 同じ問題があります

この質問は役に立ちましたか？

はい いいえ
スコア 1
コメントを追加

4件の回答

フィルタ：
参考になった順 新しい順 古い順
ベストアンサー

オプション

I was able to find the answer to the problem. I decided to totally disassemble the iPad. Upon doing so I found that a very small piece of digitizer glass was between the battery connections. It must have went in there when I place the isolator pick in. I reassembled the iPad and now it is charging.

このアンサーは役に立ちましたか？

はい いいえ
スコア 1

1件のコメント:

Awesome...sometimes it takes sharp eyes to see these tiny issues!

さんによる

コメントを追加
最も参考になった回答

オプション

There are a few possibilities here:

  • If you didn't isolate the battery when performing the repair, you may have damaged the charging circuit on the logic board.
  • You may have dislodged some of the small components near the battery connector. One of them (FL7500) allows the gas gauge IC inside the battery to communicate the charge state to the CPU. If that one gets knocked off, it could be causing your issues.

Block Image

このアンサーは役に立ちましたか？

はい いいえ
スコア 3

4 件のコメント:

Minho, after replacing iPad Air battery and digitizer I am having a problem charging. I suspect it could be one of the 2 problems you listed. What would be the solution to these 2 problems?

さんによる

@daltmann The problems I outlined require micro-soldering repairs and are not typically DIY repairs.

さんによる

Minho, would replacing the logic board fix it?

さんによる

@daltmann replacing the logic board is like replacing the device. The cost is pretty similar to buying a used device.

さんによる

コメントを追加

オプション

It charged fine before the replacement? Was the battery disconnected before the repair or did you leave it screwed in?

The digi would not cause the charging issue. First thing I would do is check for any damage to the battery or chargeport flex. It's easy to slip and nick these during the repair. If there is no signs of damage I would then try a new battery. If it charging at all then it's not likely the chargeport that's the issue.

このアンサーは役に立ちましたか？

はい いいえ
スコア 0
コメントを追加

オプション


Had the same problem it would only charge to 20 percent and then die.

opened it back up and made sure the battery was seated correctly and then it started charging correctly. The logic board has to seat properly over the new battery.

このアンサーは役に立ちましたか？

はい いいえ
スコア 0
コメントを追加

回答を追加する

Marko さん、ありがとうございました！
統計データ:

過去 24時間: 2

過去 7 日: 2

過去 30 日: 12

今までの合計 2,008