メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

2015年9月25日に発売。モデル番号はA1688 / A1633。このデバイスの修理は、前世代携帯と同様にスクリュードライバーといくつかの工具が必要です。 GSMまたはCDMA、16、64、128 ギガバイト有り /シルバー、ゴールド、スペースグレイ、ローズゴールドのカラーオプション有り。

2359の回答 すべてを表示

home button not working after battery replacement?

Hey guys i just changed my battery on my iphone 6s and my home button stopped working? i unplugged the ribbon cables everywhere and plugged them back in and nothing my home button still does not work. any ideas ?

この質問に回答する 同じ問題があります

この質問は役に立ちましたか?

スコア 7
コメントを追加

Nintendo Switch 修理キット

ゲームを再開するための、早くて簡単な修理キット

Switch 修理キットページへ

Nintendo Switch 修理キット

ゲームを再開するための、早くて簡単な修理キット

Switch 修理キットページへ

6件の回答

最も参考になった回答

If phone is opened by someone other than apple the home button doesn’t work !

If anyone knows how to reset it please let me know !

Rdsvideo3@yahoo.com

この回答は役に立ちましたか?

スコア 1
コメントを追加

If you dont make a move or doesnt move the home button while installing the battery maybe the problem is you didnt put the lcd well to the housing :)

この回答は役に立ちましたか?

スコア 0

コメント:

You may not put the ribbon cable well also on the logic board or definitely try hard resseting your phone if it doesnt solve the problem its on the hardware itself maybe you damage something inside.

さんによる

the screen is seating perfectly fine ?

さんによる

Try removing the screen and put it back again maybe the ribbon cables is not properly intact .I already encounter that on 5/5c/5s and se the only problem is the screen doesnt lie perfectly on the housing itselff if it didnt work try hard resetting the phone .do you unscrew the home button ?Or somethin on the screen ?

さんによる

Or someone blocking on the continuity of the home button to the board located at your charging port .Thats why im asking if the phone is not perfectly intact on the housing because sometimes the continuity is break because it didnt have physical contact .its like a sensor that means the phone is being pressed or not

さんによる

Just to note make sure battery is unplugged when unplugging or plugging screen cables to logic board.

Also have you tried turning phone off and on?

さんによる

コメントを追加

Hey guys! I have a problem with my iPhone 7. Its battery wa damage during charging. It gives me low battery timing. So, I replaced my battery. After that my iPhone’s home button does not working and show the pop up “ Touch id loads to fail on this iPhone”

What can I do?

Before battery replacement my iPhone wa properly working.

この回答は役に立ちましたか?

スコア 0

コメント:

Hi all

My phone is i phone 7 , my phone is 1 year and 4 months old so my battery discharge faster, so I order the battery in online and use YouTube to replace by myself. as of my knowledge, I never touch the home button area . but still when I test with new battery, I have the same issue (Unable to active touch ID). I browse lot of website finally I come to know apple software design to lock or deactivate the home button when you open by unauthorized apple store.

さんによる

I replaced the battery with a kit. Home button does not work. I broke a ribbon cable going to the screen. My fault. Heck. Suggest check all three cables going to screen.

さんによる

コメントを追加

The metal cover above the lcd cable is too tight. Loosen it and then you should be okay.

この回答は役に立ちましたか?

スコア 0
コメントを追加

If you have a screen available, try it out in a new screen. The ribbon that runs from your button to the board is part of the screen (unfortunately). That ribbon being damaged would actually be the cheapest fix, so hopefully that helps. Replacing the button or the board would be expensive.

この回答は役に立ちましたか?

スコア 0
コメントを追加

Yes the flex cable or one of the connectors in that area to the screen is being pinched down to hard by the metal cover above it. Loosen the 4/5 screws depending on your model that covers the cables and you should be fine.

この回答は役に立ちましたか?

スコア 0
コメントを追加

回答を追加する

David hoffman さん、ありがとうございました!
統計データを表示:

過去 24時間: 7

過去 7 日: 36

過去 30 日: 196

今までの合計 7,828