はじめに

Before disassembling, unplug the Camera from the PS4.

この分解は修理ガイドでは ありません。 お持ちのPlayStation Cameraを修理する際は、iFixitの修理ガイドをご利用ください。

  1. There are two PH0 Screws in the socket which hold the cable.
    • There are two PH0 Screws in the socket which hold the cable.

    • Unscrew two PH0 Screws and pull off the cable holder.

    コメントを追加する

  2. The next two PH0 Screws are located BEHIND the two polycarbonate-plates of the two camera-lenses. Take a sharp tweezer and stab under that plate. The plates are glued with a sticky tape to the housing. These plates are very fragile and will break if handled incautious.
    • The next two PH0 Screws are located BEHIND the two polycarbonate-plates of the two camera-lenses. Take a sharp tweezer and stab under that plate. The plates are glued with a sticky tape to the housing. These plates are very fragile and will break if handled incautious.

    コメントを追加する

    • There is one more PH0 screw to remove. This one is behind the other lens.

    • This was the easy part.

    コメントを追加する

    • There are many clips in there.

    コメントを追加する

  3. Fixmasのスピリットを広めましょう
    クーポンコードFIXMAS12を使えば、50ドル以上のお買い上げで12ドル割引となります。
    Fixmasのスピリットを広めましょう
    クーポンコードFIXMAS12を使えば、50ドル以上のお買い上げで12ドル割引となります。
    • Encore two photos where to locate these nasty clips

    コメントを追加する

    • The other half of the housing is attached to a solid U-Frame with the electronics.

    • There are four silver screws, PH0.

    • Four microphones, two with black/yellow cables and two with black/red wiring.

    コメントを追加する

    • The backside of the U-frame. The cable is not soldered, there is a plug.

    • Detail of the plug.

    Whats the make of the cable.. What do I search for in order to buy a new one

    Chris - 返信

    • 6 PH1 screws. Take a small magnet to hold them.

    コメントを追加する

    • The connector of the mikrophone-array

    コメントを追加する

    • The lenses, plastic, glued tight.

    • NOT ADJUSTABLE.

    コメントを追加する

    • Backside, two small PH0 at each CCD. But the Cameramodules are clued to the board,too - without destruction, you can not open it.

    • I want to save it as spare-part, so i don't want to open it. So here is finito capito. :) Thanks for watching...

    コメントを追加する

    • Extra: The wiring.

    • It's an USB3 cable without green/white Pimf. There are three SEPARATE ISOLATED metalfoil shields with wire, red-black-power and two Pimf yellow/blue and orange/green. So ja, thats it. Paulaner.

    コメントを追加する

Schwarzstein

メンバー登録日: 2013年07月15日

2,287 ポイント

14のガイドは作成済み

Only 7 steps? Where is the rest of the teardown? I wanted to see detailed images of the optics.

Alexandru Voda - 返信

Ja, okay, i made some pictures for you. The optics are in Step 10.

Enjoy.

Freundliche Grüsse. :)

Schwarzstein - 返信

Does anyone think it would be possible to cut the wires from two cameras and splice the wires together and put the power on a A/B rocker switch to switch between two cameras?

Dan Schultz - 返信

コメントを追加する

統計データを表示:

過去 24時間: 2

過去 7 日: 16

過去 30 日: 83

今までの合計 7,270