修理を始めるには コミュニティ ストア

Hoe gebruik je op maat gemaakte kleefstrips?

ガイドに戻る
英語
オランダ語
前の手順 次の手順

手順 2を翻訳中

手順2
How to Apply Custom-cut Adhesive Strips, Prepare the surface: 手順 0、 3の画像 1 How to Apply Custom-cut Adhesive Strips, Prepare the surface: 手順 0、 3の画像 2 How to Apply Custom-cut Adhesive Strips, Prepare the surface: 手順 0、 3の画像 3
Prepare the surface

  • To ensure a good adhesive bond, both your device and part need to be thoroughly cleaned. This may take some time, but the results are worth the effort.

  • Remove large chunks of adhesives with your fingers, spudger, plastic opening tool, or tweezers.

  • Don't use metal tools if you're cleaning display panels or glass covers, as the tools may scratch the surface.

  • Use adhesive remover or isopropyl alcohol (>70%) to remove residue from metal surfaces. Wipe in one direction with a lint-free cloth or coffee filter until all the adhesive residue is gone.

  • While isopropyl alcohol is generally safe to use on electronics, they will dissolve certain foam adhesives. Be careful to contain the alcohol when cleaning.

  • Allow the alcohol to completely evaporate from the device before reassembly.

Prepareer de oppervlakte

Om te zorgen dat de kleefstrips goed hechten, moet je de oppervlakte waar het op gaat kleven goed schoonmaken. Dit kan even duren, maar het resultaat is de moeite meer dan waard.

Verwijder grote stukken lijm met je vingers, spudger, plasticen openingstool of met pincetten.

Gebruik geen metalen tools bij het schoonmaken van het schermpaneel of de glazen platen, aangezien deze het glas kunnen beschadigen.

Gebruik lijmverwijderaar of hoog geconcentreerde (>90%) isopropyl alcohol om de overgebleven restjes van metalen oppervlakten te verwijderen. Veeg met een pluisvrij doek of een koffiefilter in één richting totdat alle restjes weg zijn.

Hoewel isopropyl alcohol normaal gesproken veilig is om te gebruiken in electronische apparaten, kan het sommige schuimige kleefmiddelen wegbijten. Zorg daarom dat de alcohol veilig afgesloten is tijdens het schoonmaken en laat het eerst volledig van het toestel verdampen voordat je het toestel weer in elkaar zet.

[title] Prepare the surface
-[* icon_note] To ensure a good adhesive bond, thoroughly clean the adhesion surfaces. This may take some time, but the results are worth the effort.
-[* black] Remove large chunks of adhesives with your fingers, spudger, plastic opening tool, or tweezers.
- [* icon_caution] Do not use metal tools if you are cleaning display panels or glass covers, as the tools may scratch the surface.
-[* black] Use adhesive remover or high concentration (>90%) isopropyl alcohol to remove residue from metal surfaces. Wipe in one direction with a lint-free cloth or coffee filter until all the adhesive residue is gone.
- [* icon_note] While isopropyl alcohol is generally safe to use on electronics, they will dissolve certain foam adhesives. Be careful to contain the alcohol when cleaning, and allow it to completely evaporate from the device before re-assembly.
+[* icon_note] To ensure a good adhesive bond, both your device and part need to be thoroughly cleaned. This may take some time, but the results are worth the effort.
+[* black] Remove large chunks of adhesives with your fingers, spudger, plastic opening tool, or [product|IF145-020|tweezers].
+ [* icon_caution] Don't use metal tools if you're cleaning display panels or glass covers, as the tools may scratch the surface.
+[* black] Use adhesive remover or isopropyl alcohol (>70%) to remove residue from metal surfaces. Wipe in one direction with a lint-free cloth or coffee filter until all the adhesive residue is gone.
+ [* icon_note] While isopropyl alcohol is generally safe to use on electronics, they will dissolve certain foam adhesives. Be careful to contain the alcohol when cleaning.
+ [* icon_note] Allow the alcohol to completely evaporate from the device before reassembly.

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります。