メインコンテンツにスキップ

Zeki TBQG884B Digitizer Touch Screen

必要な工具と部品

  1. Zeki TBQG884B Digitizer Touch Screen, Rear Case: 手順 1、 2の画像 1 Zeki TBQG884B Digitizer Touch Screen, Rear Case: 手順 1、 2の画像 2
    • Remove the two screws from the end of the device where the ports are located using a Phillips #1 screwdriver.

  2. Zeki TBQG884B Digitizer Touch Screen: 手順 2、 1の画像 1
    • Place the tablet down so that the screen is facing away from you.

    • Insert the tip of your opening tool into the small gap between the gray and white plastic covering. Pry it open and you should hear the clips opening up.

    • Gently work your way around the perimeter of the tablet's edge.

  3. Zeki TBQG884B Digitizer Touch Screen: 手順 3、 2の画像 1 Zeki TBQG884B Digitizer Touch Screen: 手順 3、 2の画像 2
    • Remove the back cover

    • Remove any tape on the speaker and detach the speaker from the back plate.

    • The speaker is connected to the motherboard by two soldered wires. Don't break them when you remove the speaker.

  4. Zeki TBQG884B Digitizer Touch Screen, Motherboard: 手順 4、 1の画像 1
    • Disconnect the Wi-Fi antenna cable from the motherboard.

  5. Zeki TBQG884B Digitizer Touch Screen: 手順 5、 1の画像 1
    • Using the Phillips #1 screwdriver, remove the three screws from the motherboard..

  6. Zeki TBQG884B Digitizer Touch Screen: 手順 6、 1の画像 1
    • Open the ZIF connector. Then, remove the ribbon that connects the motherboard and the screen.

  7. Zeki TBQG884B Digitizer Touch Screen: 手順 7、 1の画像 1
    • Disconnect the other ZIF connector on the opposite side of the motherboard.

  8. Zeki TBQG884B Digitizer Touch Screen: 手順 8、 1の画像 1
    • Remove the motherboard and now reinsert all connectors into a new motherboard.

    • In order to disconnect the battery and speaker wires from the motherboard, soldering is required. Be cautious as the soldering iron is hot.

  9. Zeki TBQG884B Digitizer Touch Screen, LCD Screen: 手順 9、 1の画像 1
    • Use an opening tool to detach the clip between the front frame, and the metal loader.

    • There are several clips on each side of the frame. Detach ALL of them before you open the loader.

  10. Zeki TBQG884B Digitizer Touch Screen: 手順 10、 1の画像 1
    • Lift the metal loader up and separate it from the LCD screen.

    • Detach each piece slowly to avoid damaging or dropping any fragile parts.

  11. Zeki TBQG884B Digitizer Touch Screen, Digitizer Touch Screen: 手順 11、 1の画像 1
    • Separate the display from the digitizer.

終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

9人の作成者と共同で作成されました。

David Wyman

メンバー登録日: 09/16/15

343 ポイント

3のガイドは作成済み

チーム

IUPUI, Team 1-3, Harley Fall 2015 IUPUI, Team 1-3, Harley Fall 2015人のメンバー

IUPUI-HARLEY-F15S1G3

5 メンバー

5のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 3

今までの合計 800