はじめに

This guide will show you how to remove the processor on your HP Compaq dx2000MT.

Turn off your computer and remove the power cable by pulling it straight out of its socket.
  • Turn off your computer and remove the power cable by pulling it straight out of its socket.

コメントを追加する

Remove the 2 Phillips #2 screws that secure the case door to the device. Remove the 2 Phillips #2 screws that secure the case door to the device.
  • Remove the 2 Phillips #2 screws that secure the case door to the device.

コメントを追加する

Remove the side case door by pushing towards the rear of the device with your hand. This may take considerable force so keep pushing! Once you slide the door back, remove it by pulling it outwards from the device.
  • Remove the side case door by pushing towards the rear of the device with your hand.

    • This may take considerable force so keep pushing!

  • Once you slide the door back, remove it by pulling it outwards from the device.

コメントを追加する

Remove the side case door by pushing towards the rear of the device with your hand. Once again, this may take considerable force. Once you slide the door back, remove it by pulling it outwards from the device.
  • Remove the side case door by pushing towards the rear of the device with your hand.

    • Once again, this may take considerable force.

  • Once you slide the door back, remove it by pulling it outwards from the device.

コメントを追加する

Remove the IDE data cable and the power cable from the optical drive by pulling away from the drive. Remove the IDE data cable and the power cable from the optical drive by pulling away from the drive. Remove the IDE data cable and the power cable from the optical drive by pulling away from the drive.
  • Remove the IDE data cable and the power cable from the optical drive by pulling away from the drive.

コメントを追加する

Remove the 2 Torx T15 screws holding the optical drive in place. Remove the 2 Torx T15 screws holding the optical drive in place.
  • Remove the 2 Torx T15 screws holding the optical drive in place.

コメントを追加する

Remove the other 2 Torx T15 screws holding the other side of the drive in place. Remove the other 2 Torx T15 screws holding the other side of the drive in place.
  • Remove the other 2 Torx T15 screws holding the other side of the drive in place.

コメントを追加する

Remove the optical drive by sliding it out the front of the device. Remove the optical drive by sliding it out the front of the device. Remove the optical drive by sliding it out the front of the device.
  • Remove the optical drive by sliding it out the front of the device.

コメントを追加する

Remove the IDE data and power cables from the hard drive Remove the IDE data and power cables from the hard drive Remove the IDE data and power cables from the hard drive
  • Remove the IDE data and power cables from the hard drive

コメントを追加する

Remove the front bezel by pulling upwards and out from below the lowest air vent. Remove the front bezel by pulling upwards and out from below the lowest air vent. Remove the front bezel by pulling upwards and out from below the lowest air vent.
  • Remove the front bezel by pulling upwards and out from below the lowest air vent.

コメントを追加する

Remove the external drive faceplate by removing the 2 Torx T15 Screws Remove the external drive faceplate by removing the 2 Torx T15 Screws Remove the external drive faceplate by removing the 2 Torx T15 Screws
  • Remove the external drive faceplate by removing the 2 Torx T15 Screws

コメントを追加する

Remove the following screws: Front Torx T15.
  • Remove the following screws:

    • Front Torx T15.

    • Torx T15 mounting the hard drive cage to the optical drive bay.

コメントを追加する

Fully remove the hard drive cage by sliding it towards the back of the device and pulling down. Fully remove the hard drive cage by sliding it towards the back of the device and pulling down. Fully remove the hard drive cage by sliding it towards the back of the device and pulling down.
  • Fully remove the hard drive cage by sliding it towards the back of the device and pulling down.

コメントを追加する

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Remove 2 Torx T15 screws holding this side of the hard drive in place Remove 2 Torx T15 screws holding this side of the hard drive in place Remove 2 Torx T15 screws holding this side of the hard drive in place
  • Remove 2 Torx T15 screws holding this side of the hard drive in place

コメントを追加する

Proceed to the other side of the hard drive cage Remove 2 Torx T15 screws holding this side of the hard drive in place Remove 2 Torx T15 screws holding this side of the hard drive in place
  • Proceed to the other side of the hard drive cage

  • Remove 2 Torx T15 screws holding this side of the hard drive in place

コメントを追加する

Remove the hard drive from the hard drive cage by pulling it outward from the cage Remove the hard drive from the hard drive cage by pulling it outward from the cage
  • Remove the hard drive from the hard drive cage by pulling it outward from the cage

コメントを追加する

Remove the Torx T15 screwdriver holding the PCI card in place. Remove the Torx T15 screwdriver holding the PCI card in place.
  • Remove the Torx T15 screwdriver holding the PCI card in place.

コメントを追加する

Remove the PCI card by pulling it out towards the side of the device.
  • Remove the PCI card by pulling it out towards the side of the device.

  • Be careful about touching the top and bottom of the card! The static electricity in your fingers could short it. If you can, only touch the metal bracket and the sides of the card.

コメントを追加する

Remove the 3 prong power connector from the motherboard by pulling it outwards toward the side of the device. Remove the 3 prong power connector from the motherboard by pulling it outwards toward the side of the device. Remove the 3 prong power connector from the motherboard by pulling it outwards toward the side of the device.
  • Remove the 3 prong power connector from the motherboard by pulling it outwards toward the side of the device.

コメントを追加する

Remove the 4 push fasteners from the case by: Prying them outwards with a small flathead screwdriver and Pulling them out with tweezers or plyers.
  • Remove the 4 push fasteners from the case by:

    • Prying them outwards with a small flathead screwdriver and

    • Pulling them out with tweezers or plyers.

コメントを追加する

Remove the fan from the case by pulling it towards the front of the device. Remove the fan from the case by pulling it towards the front of the device. Remove the fan from the case by pulling it towards the front of the device.
  • Remove the fan from the case by pulling it towards the front of the device.

コメントを追加する

Release the lower portion of the RAM by pushing down on the bottom tab. Release the lower portion of the RAM by pushing down on the bottom tab.
  • Release the lower portion of the RAM by pushing down on the bottom tab.

コメントを追加する

Release the upper portion of the RAM by pushing down on the upper tab. Release the upper portion of the RAM by pushing down on the upper tab.
  • Release the upper portion of the RAM by pushing down on the upper tab.

コメントを追加する

Remove the RAM by pulling it out towards the side of the device Be careful about touching the top (right) and bottom (left)sides of the RAM! The static electricity in your fingers could short it. If you can, only touch the top and bottom of the RAM. If replacing RAM, make sure it is the right type, speed, and size for your computer. Otherwise the RAM may not fit or your computer may not start up.
  • Remove the RAM by pulling it out towards the side of the device

  • Be careful about touching the top (right) and bottom (left)sides of the RAM! The static electricity in your fingers could short it. If you can, only touch the top and bottom of the RAM.

  • If replacing RAM, make sure it is the right type, speed, and size for your computer. Otherwise the RAM may not fit or your computer may not start up.

コメントを追加する

Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.
  • Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

コメントを追加する

Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.
  • Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

コメントを追加する

Remove the 4 Torx T15 screws from the rear of the power supply Remove the 4 Torx T15 screws from the rear of the power supply Remove the 4 Torx T15 screws from the rear of the power supply
  • Remove the 4 Torx T15 screws from the rear of the power supply

コメントを追加する

Slide the power supply towards the front of the device Keep your hand underneath it! You don't want to drop it!
  • Slide the power supply towards the front of the device

  • Keep your hand underneath it! You don't want to drop it!

  • Then pull the power supply down and remove it from the case.

コメントを追加する

Remove any IDE cables from the motherboard by pulling them out towards the side of the device. Remove any IDE cables from the motherboard by pulling them out towards the side of the device. Remove any IDE cables from the motherboard by pulling them out towards the side of the device.
  • Remove any IDE cables from the motherboard by pulling them out towards the side of the device.

コメントを追加する

Remove the 2 prong speaker connector by pulling out towards the side of the device. Remove the 2 prong speaker connector by pulling out towards the side of the device.
  • Remove the 2 prong speaker connector by pulling out towards the side of the device.

コメントを追加する

Remove the 16 pin connector from the motherboard by pulling it out towards the side of the device. Remove the 16 pin connector from the motherboard by pulling it out towards the side of the device.
  • Remove the 16 pin connector from the motherboard by pulling it out towards the side of the device.

コメントを追加する

Remove the 14 pin USB connector by pulling it out towards the side of the device. Remove the 14 pin USB connector by pulling it out towards the side of the device.
  • Remove the 14 pin USB connector by pulling it out towards the side of the device.

コメントを追加する

Remove the 8 Torx T15 screws from the motherboard. Remove the 8 Torx T15 screws from the motherboard.
  • Remove the 8 Torx T15 screws from the motherboard.

コメントを追加する

Remove the 3 pin power connector by pulling it out towards the side of the device. Remove the 3 pin power connector by pulling it out towards the side of the device.
  • Remove the 3 pin power connector by pulling it out towards the side of the device.

コメントを追加する

Unscrew the 4 Torx T15 screws holding the CPU Cooler in place. Make sure to hold your cpu cooler when removing the screws. You don't want it to fall!
  • Unscrew the 4 Torx T15 screws holding the CPU Cooler in place.

  • Make sure to hold your cpu cooler when removing the screws. You don't want it to fall!

コメントを追加する

Remove the cpu cooler by pulling out towards the side of the device. Make sure you do not touch where the cpu cooler makes contact with the processor! You do not want to contaminate the thermal paste that separates these components.
  • Remove the cpu cooler by pulling out towards the side of the device.

  • Make sure you do not touch where the cpu cooler makes contact with the processor! You do not want to contaminate the thermal paste that separates these components.

  • When replacing your cpu cooler, make sure you clean the processor contact area on the cooler and processor with isopropyl rubbing alcohol.

コメントを追加する

Remove the motherboard by pushing it forwards and removing it from the case. Remove the motherboard by pushing it forwards and removing it from the case.
  • Remove the motherboard by pushing it forwards and removing it from the case.

コメントを追加する

Lift up the bar that secures the processor to the motherboard Lift up the bar that secures the processor to the motherboard Lift up the bar that secures the processor to the motherboard
  • Lift up the bar that secures the processor to the motherboard

コメントを追加する

Lift the processor up and out of its socket. When doing this make sure to grasp it from opposite sides. Touching the pins and/or lifting it not straight up may bend the pins making it useless! Notice the yellow framed triangle in the third picture. The processor must be put back in with this facing the same way to avoid damage. Never force a processor into its socket because it is either not aligned or has bent pins.
  • Lift the processor up and out of its socket.

  • When doing this make sure to grasp it from opposite sides. Touching the pins and/or lifting it not straight up may bend the pins making it useless!

  • Notice the yellow framed triangle in the third picture. The processor must be put back in with this facing the same way to avoid damage. Never force a processor into its socket because it is either not aligned or has bent pins.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Logan Pace

メンバー登録日: 2011年10月12日

2,020 ポイント

15のガイドは作成済み

チーム

Cal Poly, Team 17-16, Regan Fall 2011 Cal Poly, Team 17-16, Regan Fall 2011人のメンバー

CPSU-REGAN-F11S17G16

4 メンバー

17のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 11

今までの合計 3,078