はじめに

This guide will show you how to remove the motherboard on your HP Compaq dx2000MT

  1. Turn off your computer and remove the power cable by pulling it straight out of its socket.
    • Turn off your computer and remove the power cable by pulling it straight out of its socket.

    コメントを追加する

  2. Remove the 2 Phillips #2 screws that secure the case door to the device.
    • Remove the 2 Phillips #2 screws that secure the case door to the device.

    コメントを追加する

    • Remove the side case door by pushing towards the rear of the device with your hand.

      • This may take considerable force so keep pushing!

    • Once you slide the door back, remove it by pulling it outwards from the device.

    コメントを追加する

    • Remove the side case door by pushing towards the rear of the device with your hand.

      • Once again, this may take considerable force.

    • Once you slide the door back, remove it by pulling it outwards from the device.

    it’s useless my friends

    bisous sur les fesses de ta mamaa

    Albert einstein - 返信

    • Remove the IDE data cable and the power cable from the optical drive by pulling away from the drive.

    コメントを追加する

    • Remove the 2 Torx T15 screws holding the optical drive in place.

    コメントを追加する

    • Remove the other 2 Torx T15 screws holding the other side of the drive in place.

    コメントを追加する

    • Remove the optical drive by sliding it out the front of the device.

    コメントを追加する

    • Remove the IDE data and power cables from the hard drive

    コメントを追加する

    • Remove the front bezel by pulling upwards and out from below the lowest air vent.

    コメントを追加する

    • Remove the external drive faceplate by removing the 2 Torx T15 Screws

    コメントを追加する

    • Remove the following screws:

      • Front Torx T15.

      • Torx T15 mounting the hard drive cage to the optical drive bay.

    コメントを追加する

    • Fully remove the hard drive cage by sliding it towards the back of the device and pulling down.

    コメントを追加する

    • Remove 2 Torx T15 screws holding this side of the hard drive in place

    コメントを追加する

    • Proceed to the other side of the hard drive cage

    • Remove 2 Torx T15 screws holding this side of the hard drive in place

    コメントを追加する

    • Remove the hard drive from the hard drive cage by pulling it outward from the cage

    コメントを追加する

    • Remove the 3 prong power connector from the motherboard by pulling it outwards toward the side of the device.

    コメントを追加する

    • Remove the 4 push fasteners from the case by:

      • Prying them outwards with a small flathead screwdriver and

      • Pulling them out with tweezers or plyers.

    コメントを追加する

    • Remove the fan from the case by pulling it towards the front of the device.

    コメントを追加する

    • Remove the Torx T15 screwdriver holding the PCI card in place.

    コメントを追加する

    • Remove the PCI card by pulling it out towards the side of the device.

    • Be careful about touching the top and bottom of the card! The static electricity in your fingers could short it. If you can, only touch the metal bracket and the sides of the card.

    コメントを追加する

    • Release the lower portion of the RAM by pushing down on the bottom tab.

    コメントを追加する

    • Release the upper portion of the RAM by pushing down on the upper tab.

    コメントを追加する

    • Remove the RAM by pulling it out towards the side of the device

    • Be careful about touching the top (right) and bottom (left)sides of the RAM! The static electricity in your fingers could short it. If you can, only touch the top and bottom of the RAM.

    • If replacing RAM, make sure it is the right type, speed, and size for your computer. Otherwise the RAM may not fit or your computer may not start up.

    コメントを追加する

    • Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

    コメントを追加する

    • Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

    コメントを追加する

    • Remove the 4 Torx T15 screws from the rear of the power supply

    コメントを追加する

    • Slide the power supply towards the front of the device

    • Keep your hand underneath it! You don't want to drop it!

    • Then pull the power supply down and remove it from the case.

    コメントを追加する

    • Remove any IDE cables from the motherboard by pulling them out towards the side of the device.

    コメントを追加する

    • Remove the 2 prong speaker connector by pulling out towards the side of the device.

    コメントを追加する

    • Remove the 16 pin connector from the motherboard by pulling it out towards the side of the device.

    コメントを追加する

    • Remove the 14 pin USB connector by pulling it out towards the side of the device.

    コメントを追加する

    • Remove the 8 Torx T15 screws from the motherboard.

    コメントを追加する

    • Remove the 3 pin power connector by pulling it out towards the side of the device.

    コメントを追加する

    • Unscrew the 4 Torx T15 screws holding the CPU Cooler in place.

    • Make sure to hold your cpu cooler when removing the screws. You don't want it to fall!

    コメントを追加する

    • Remove the cpu cooler by pulling out towards the side of the device.

    • Make sure you do not touch where the cpu cooler makes contact with the processor! You do not want to contaminate the thermal paste that separates these components.

    • When replacing your cpu cooler, make sure you clean the processor contact area on the cooler and processor with isopropyl rubbing alcohol.

    コメントを追加する

    • Remove the motherboard by pushing it forwards and removing it from the case.

    コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

16 の人々がこのガイドを完成させました。

Logan Pace

メンバー登録日: 2011年10月12日

2,020 ポイント

9のガイドは作成済み

チーム

Cal Poly, Team 17-16, Regan Fall 2011 Cal Poly, Team 17-16, Regan Fall 2011人のメンバー

CPSU-REGAN-F11S17G16

4 メンバー

17のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 4

過去 30 日: 25

今までの合計 8,777