Protocol Slipstream WiFi Propeller Motor Replacement

はじめに

If your Protocol Slipstream WiFi (model number 6182-3MXB) has a broken propeller motor on it, use this guide to replace the propeller motor. The propeller motor is what spins the propeller that actually produces the air that lifts the device off the ground. If the propeller motor is broken the propeller will not spin at all causing the drone not to lift off the ground correctly and immediately crash. Be careful not to replace the propeller motor with the device turned on. The propeller spins very fast and can be potentially harmful. The Slipstream WiFi has 4 propeller motors on it. Each motor has 2 wires and those wires connect to different spots on the device’s computer. Do not attempt to change more than one motor at a time. It is very easy to get the wires mixed up and forget where they go. Make sure to always label what color wire goes where before you pull the motor off the device. The repair guide includes soldering on a very small computer, so proficient soldering skills are a plus.

必要な工具と部品

手順1 Propeller

Protocol Slipstream WiFi Propeller Motor Replacement, Propeller: 手順 1、 1の画像 1

Remove the 4.5 mm Philips #00 screw that holds the propeller in place.

編集

手順2

Lift the propeller off the device
Note: When sliding on the new propeller, make sure to align the groove on the propeller with the shaft of the gear. If aligned correctly the propeller should slide on smoothly.
There are two different propellers that go on the device. Each propeller has a 3 or 4 written on it. Be sure to replace the propeller with a new propeller with the matching number.

編集

手順3 Propeller Guards

Protocol Slipstream WiFi Propeller Motor Replacement, Propeller Guards: 手順 3、 1の画像 1

There are 3 points where the propeller guard attaches to the device.
Place one finger on the body (black object) of the device and one finger under the propeller guard (silver object) and gently but firmly push the propeller guard up until it disconnects from the body at the 3 points circled in red.
There are two propeller guards on the device. One for each set of propellers. Each propeller guard has two locations that you have these 3 tabs to remove until you can replace it.

編集

手順4 Propeller Motor

Protocol Slipstream WiFi Propeller Motor Replacement, Propeller Motor: 手順 4、 2の画像 1

Protocol Slipstream WiFi Propeller Motor Replacement, Propeller Motor: 手順 4、 2の画像 2

Remove the four 5.5 mm Philips #00 screws that hold the lower canopy to the upper canopy.
Gently pull the lower canopy up and towards the back of the drone. The lower canopy will still be attached to the upper canopy by 3 wires. Just set the lower canopy aside and continue with the repair.
Be very careful when pulling the lower canopy apart from the upper canopy. There are 3 wires that will still be attached between the lower and upper canopies.

編集

手順5

Remove the two 4.5 mm Philips #00 screws that hold the motor cover onto the upper canopy.
Gently pull up on the motor cover until it disconnects from the upper canopy.

編集

手順6

Grab the motor and pull the motor out of the upper canopy slot.
Be careful pulling the motor out of the slot in the upper canopy. The motor will still be attached to the main computer by 2 wires.

編集

手順7

At this point, pay attention to where each color wire attaches to the computer. Write down which color wire goes where.
It is very important that you connect the new motor wires in the same location as the old wires and pay attention to which color wire attaches to each location.

編集

手順8

この手順で使用する道具：

Desoldering Pump

$3.99

購入する

Use your soldering iron and heat up the solder that holds the two wires from the motor to the main computer. Once the solder melts use your desoldering pump to desolder the wires to the main computer.
At this point the motor can be completely removed. You will need to solder the new motor wires in the same spot as the old motor wires.
For more information on soldering and desoldering connections, please read the How to Solder and Desolder Connections guide.