メニュー

あなたの設定

私のワークベンチ

お持ちのデバイス用の修理ガイド、交換用パーツやアンサーフォーラムにアクセスする。
カート

カートには何も入っていません。

当社のショップを閲覧する

PowerBook G4 Titanium Mercury Hard Drive Replacement

おすすめ

作成者： iRobot (そして 3 人のその他投稿者)
  • コメント: 0
  • お気に入り: 1
  • 完了: 14

おすすめのガイド

難易度

簡単

手順

9

所要時間

必要時間を提案??

セクション

3

フラグ

1

Featured Guide

おすすめのガイド

このガイドはiFixitスタッフによって太鼓判が押されています。

はじめに

You can install hard drives up to 12.5mm thick.

ツール

これらのツールを購入する

パーツ

    • Turn the G4 over.

    • Remove the eight Phillips screws from the lower case.

    翻訳

  2. Using your thumbs, slide the lower case away from you.

    • Using your thumbs, slide the lower case away from you.

    • The lower case may stick in the front on a tab just above the center of the DVD drive. Be careful as you work the case off, or you may break the thin strip of plastic just above the drive.

    • Lift the lower case off.

    翻訳

  3. Your laptop should look approximately like this.

    • Your laptop should look approximately like this.

    翻訳

  4. iPhoneのバッテリーキット

    Only $29.99

    Buy Now

    iPhoneのバッテリーキット

    Only $29.99

    Buy Now

  5. Disconnect the hard drive ribbon from the logic board using a spudger or the tip of your finger.

    • Disconnect the hard drive ribbon from the logic board using a spudger or the tip of your finger.

    翻訳

  6. To free the hard drive, remove the two T8 Torx screws from the right wall of the battery housing.

    • To free the hard drive, remove the two T8 Torx screws from the right wall of the battery housing.

    翻訳

  7. Remove the hard drive by gently grasping the orange ribbon cable and lifting the left edge up and out of the computer.

    • Remove the hard drive by gently grasping the orange ribbon cable and lifting the left edge up and out of the computer.

    • There are four rubber bumpers that fit over the hard drive screws. Ensure that these bumpers come out when you remove the hard drive.

    翻訳

  8. Your laptop should look approximately like this.

    • Your laptop should look approximately like this.

    翻訳

  9. Remove the two black plastic bumpers and two T8 Torx screws from the side of the hard drive.

    • Remove the two black plastic bumpers and two T8 Torx screws from the side of the hard drive.

    翻訳

  10. Grasp the orange ribbon cable and disconnect it from the hard drive. If the connector is tight, gently rock it from side to side.

    • Grasp the orange ribbon cable and disconnect it from the hard drive. If the connector is tight, gently rock it from side to side.

    • Be sure to pull evenly on both sides as uneven force may damage the hard drive pins and render your data inaccessible.

    • If you are installing a new hard drive, we have an OS X install guide to get you up and running.

    翻訳
まとめ

To reassemble your device, follow these instructions in reverse order.

14 の人々がこのガイドを完成させました。

添付文書

作成者

3他の投稿者と一緒に

iRobot

メンバー登録日: 2009年09月24日

1 ポイント

623のガイドは作成済み

バッジ: 35

+32 個以上のバッジ

0コメント

コメントを追加

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 6

過去 30 日: 26

今までの合計 17,368