メインコンテンツにスキップ

はじめに

This guide will show the steps to dismantle the move controller and remove the battery in order to have it replaced.

パーツ

パーツは指定されていません。

  1. Using a Phillips #0 screwdriver,  remove the four 10mm screws located on the back of the device. Using a Phillips #0 screwdriver,  remove the four 10mm screws located on the back of the device. Using a Phillips #0 screwdriver,  remove the four 10mm screws located on the back of the device.
    • Using a Phillips #0 screwdriver, remove the four 10mm screws located on the back of the device.

  2. Insert the plastic opening tool at the indent. Gently use a forward and backward motion to safely pop open the cover.
    • Insert the plastic opening tool at the indent.

    • Gently use a forward and backward motion to safely pop open the cover.

    • Using your hands to further pull it apart.

  3. Once the device is opened, lift the battery out of the black plastic holder. Carefully pull the battery out and ensure that it's wires are still connected to the inside.
    • Once the device is opened, lift the battery out of the black plastic holder.

    • Carefully pull the battery out and ensure that it's wires are still connected to the inside.

    You can disconnect the back/trigger assembly ribbon cable at this point by proceeding to Steps 13/14 (without the other steps for disassembly as they are unnecessary for replacing just the trigger).

    Peter Miller - 返信

  4. Using a Phillips head screwdriver, remove the 9mm screw located to the right of the battery, which is connected to  the inner plastic frame. Using the plastic opening tool carefully take out the grey cylindrical piece (vibrator) that is also attached to a wire. Using the plastic opening tool carefully take out the grey cylindrical piece (vibrator) that is also attached to a wire.
    • Using a Phillips head screwdriver, remove the 9mm screw located to the right of the battery, which is connected to the inner plastic frame.

    • Using the plastic opening tool carefully take out the grey cylindrical piece (vibrator) that is also attached to a wire.

  5. Gently pull out the small grey cylindrical piece (vibrator). Removing this piece makes it easier to access the wire connection of the battery and remove it.
    • Gently pull out the small grey cylindrical piece (vibrator).

    • Removing this piece makes it easier to access the wire connection of the battery and remove it.

  6. Using tweezers, remove the small piece with a cylindrical top that is located to the left of the inner plastic frame. Using tweezers, remove the small piece with a cylindrical top that is located to the left of the inner plastic frame.
    • Using tweezers, remove the small piece with a cylindrical top that is located to the left of the inner plastic frame.

  7. Using one hand to hold the device, and the other hand to squeeze the inner plastic frame. Remove by squeezing the inner plastic frame, lift and pull it towards you. While removing the frame, be extremely careful because it could damage the frame or the motherboard.
    • Using one hand to hold the device, and the other hand to squeeze the inner plastic frame.

    • Remove by squeezing the inner plastic frame, lift and pull it towards you.

    • While removing the frame, be extremely careful because it could damage the frame or the motherboard.

  8. Gently pull on the white piece connecting the battery and the connector. Gently pull on the white piece connecting the battery and the connector.
    • Gently pull on the white piece connecting the battery and the connector.

終わりに

To reassemble your device, follow these instructions in reverse order.

6 の人々がこのガイドを完成させました。

Jenelle Mohammed

メンバー登録日: 2016年09月28日

193 ポイント

1ガイドが承認済み

チーム

USF Tampa, Team 3-3, Passmore Fall 2016 USF Tampa, Team 3-3, Passmore Fall 2016人のメンバー

USFT-PASSMORE-F16S3G3

4 メンバー

8のガイドは作成済み

4 件のコメント

When putting the plastic battery rig back in on my second time doing this, I bent one of the little plastic pins that fits into a hole in the PCB. Definitely want to be careful with that. To make it a bit easier, I unscrewed the bottom port PCB part of the way so I could take the bottom plastic housing and put the plastic battery rig in straight. It made it a lot easier.

Burke Cates - 返信

No need to take out the motor, just use sharp tweezers and grab the connector (NOT the wires) and with small wiggling pull it out. Worked for mine.

crus - 返信

Worked great! Thanks for this. I did not need to take out the black battery / motor piece. Tweezers worked great to remove and install the battery cable

Harry Skigis - 返信

Any recommended online / physical store to buy new batteries for this because ifixit doesn’t have them?

Silas Stewart - 返信

コメントを追加

統計データを表示:

過去 24時間: 1

過去 7 日: 19

過去 30 日: 87

今までの合計 10,557