メインコンテンツにスキップ

Ozeri Pronto ZK14-S Wire Replacement

必要な工具と部品

  1. Ozeri Pronto ZK14-S Wire Replacement, Panel Removal: 手順 1、 2の画像 1 Ozeri Pronto ZK14-S Wire Replacement, Panel Removal: 手順 1、 2の画像 2
    • Twist the plastic plate slowly to the left to pull it away.

  2. Ozeri Pronto ZK14-S Wire Replacement: 手順 2、 1の画像 1
    • Lift up the sticker at the bottom where the “Ozeri” logo is to reveal a screw.

    • The sticker does not need to be completely removed.

  3. Ozeri Pronto ZK14-S Wire Replacement: 手順 3、 1の画像 1
    • Using a 2.0 Flathead screwdriver, remove the 9.50 mm Phillips head screw under the sticker.

  4. Ozeri Pronto ZK14-S Wire Replacement: 手順 4、 2の画像 1 Ozeri Pronto ZK14-S Wire Replacement: 手順 4、 2の画像 2
    • Using a 2.0 Flathead screwdriver, remove the two 18.76 mm Phillips head screws in the plate stand.

  5. Ozeri Pronto ZK14-S Wire Replacement: 手順 5、 2の画像 1 Ozeri Pronto ZK14-S Wire Replacement: 手順 5、 2の画像 2
    • Using a 2.0 Flathead screwdriver, remove the 9.44 mm Phillips head screw on the edge opposite to the LCD screen.

  6. Ozeri Pronto ZK14-S Wire Replacement: 手順 6、 1の画像 1
    • Turn the device over so the back panel is facing up.

  7. Ozeri Pronto ZK14-S Wire Replacement: 手順 7、 1の画像 1
    • Using the iFixit opening tool, pry off the two rubber stubs on the right side and the two rubber stubs on the left side of the bottom of the device.

  8. Ozeri Pronto ZK14-S Wire Replacement: 手順 8、 1の画像 1
    • Using a 2.0 Flathead screwdriver, remove the four 9.46 mm Phillips head screws that were under the rubber stubs.

  9. Ozeri Pronto ZK14-S Wire Replacement: 手順 9、 2の画像 1 Ozeri Pronto ZK14-S Wire Replacement: 手順 9、 2の画像 2
    • Pry apart the two panels to separate them from each other.

    • Flip the device over so the LCD is facing up. Flip the front panel over on its side.

    • Be careful when separating the panels to avoid damaging the wires they are connected by.

  10. Ozeri Pronto ZK14-S Wire Replacement, Wire: 手順 10、 2の画像 1 Ozeri Pronto ZK14-S Wire Replacement, Wire: 手順 10、 2の画像 2
    この手順で使用する道具:
    Flathead 3/32" or 2.5 mm Screwdriver
    $5.49
    購入する
    • Using the 2.0 Flathead screwdriver, remove the three 7.20 mm screws on the back of the center LCD motherboard.

  11. Ozeri Pronto ZK14-S Wire Replacement: 手順 11、 1の画像 1
    • Stand the center motherboard up.

    • Be careful when standing up the LCD motherboard to avoid damaging the wires it is connected to.

  12. Ozeri Pronto ZK14-S Wire Replacement: 手順 12、 1の画像 1
    • Desolder the post the damaged wire is attached to on the motherboard.

    • Use caution when handling the soldering iron since it can get very hot.

  13. Ozeri Pronto ZK14-S Wire Replacement: 手順 13、 1の画像 1
    • Using the iOpener, warm the glue on the weight sensor the other end of the damaged wire is attached to.

    • Use caution when handling the iOpener since it can get very hot.

    • Refer to the following guide for detailed instructions on how to use the iOpener: iOpener (Legacy) Instructions

  14. Ozeri Pronto ZK14-S Wire Replacement: 手順 14、 1の画像 1
    • Using the nylon or metal spudger, detach the end of the damaged wire from the weight sensor.

    • Repeat steps 13 and 14 to remove the end of a damaged wire from the other two motherboards.

終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

3人の作成者と共同で作成されました。

Oneika White

メンバー登録日: 10/01/15

709 ポイント

4のガイドは作成済み

チーム

USF Tampa, Team 1-4, Leahy Fall 2015 USF Tampa, Team 1-4, Leahy Fall 2015人のメンバー

USFT-LEAHY-F15S1G4

4 メンバー

5のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 4

過去 7 日: 16

過去 30 日: 56

今までの合計 4,226