メインコンテンツにスキップ

はじめに

Removing the power cord is straightforward, but it does require soldering.

  1. Oster 6329 Power Cord Replacement, Outer Shell Removal: 手順 1、 2の画像 1 Oster 6329 Power Cord Replacement, Outer Shell Removal: 手順 1、 2の画像 2
    • Using the Phillips-head #2 screwdriver, unscrew the three 1cm Phillips-head screws on the plastic base of the toaster to separate the outer metal shell from the plastic base.

  2. Oster 6329 Power Cord Replacement: 手順 2、 1の画像 1
    • Push the plastic push-down handle down and pull the plastic handle straight from metal arm.

  3. Oster 6329 Power Cord Replacement: 手順 3、 1の画像 1
    • Loosen the outer metal shell from the plastic base by holding the plastic base while pulling up on the metal shell.

    • Only lift the outer shell a little so as not to disconnect the cables that connect the circuit board.

  4. Oster 6329 Power Cord Replacement: 手順 4、 2の画像 1 Oster 6329 Power Cord Replacement: 手順 4、 2の画像 2
    • Disconnect the cable clips from the circuit board using the tweezers to free the outer metal shell from the plastic base.

  5. Oster 6329 Power Cord Replacement: 手順 5、 2の画像 1 Oster 6329 Power Cord Replacement: 手順 5、 2の画像 2
    • Lift the top outer metal shell.

    • Carefully lift the outer metal shell at an angle so as not to damage the components in the front of the toaster.

  6. Oster 6329 Power Cord Replacement, Power Cord: 手順 6、 1の画像 1
    • Using a flat-head screwdriver, pry the power cord from the base of the toaster.

  7. Oster 6329 Power Cord Replacement: 手順 7、 1の画像 1
    • Using a flat-head screwdriver, pry the white wire from the base.

  8. Oster 6329 Power Cord Replacement: 手順 8、 1の画像 1
    • Locate the circuit board at the front of the toaster where the power cord and white wire meet.

    • Pull the circuit board up and out to free the circuit board from the body of the toaster.

    • It is tightly fit and may take moderate force to remove.

  9. Oster 6329 Power Cord Replacement: 手順 9、 2の画像 1 Oster 6329 Power Cord Replacement: 手順 9、 2の画像 2
    • Desolder the power cord from the circuit board at the locations show in the diagram.

    • For soldering instructions see the iFixit Soldering Guide.

    • The wires should be free from board when un-soldering is complete.

  10. Oster 6329 Power Cord Replacement: 手順 10、 2の画像 1 Oster 6329 Power Cord Replacement: 手順 10、 2の画像 2
    • Unscrew the two 1.5cm Phillips-head screws at the back of the toaster that are holding the power cord in place to remove the retaining clip.

    • Remove the plastic retaining clip that is holding the cord in place.

  11. Oster 6329 Power Cord Replacement: 手順 11、 2の画像 1 Oster 6329 Power Cord Replacement: 手順 11、 2の画像 2
    • Untie the knot in the power cord.

  12. Oster 6329 Power Cord Replacement: 手順 12、 1の画像 1
    • Pull the cord from the base to remove the cable.

終わりに

To reassemble your device, follow these instructions in reverse order.

Timothy Grijalva

メンバー登録日: 2014年01月31日

210 ポイント

2のガイドは作成済み

チーム

Cal Poly, Team 13-15, Regan Winter 2014 Cal Poly, Team 13-15, Regan Winter 2014人のメンバー

CPSU-REGAN-W14S13G15

5 メンバー

6のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 14

今までの合計 572