1. Remove the Blender Container from the Blender Base. Remove the Blender Container from the Blender Base.
    • Remove the Blender Container from the Blender Base.

  2. Flip the blender so the bottom is facing you. Flip the blender so the bottom is facing you.
    • Flip the blender so the bottom is facing you.

  3. Unscrew the 16mm screws located on the plastic bottom from the blender base using a Phillips #2 screwdriver. Unscrew the 16mm screws located on the plastic bottom from the blender base using a Phillips #2 screwdriver. Unscrew the 16mm screws located on the plastic bottom from the blender base using a Phillips #2 screwdriver.
    • Unscrew the 16mm screws located on the plastic bottom from the blender base using a Phillips #2 screwdriver.

  4. Free shipping on all orders over $100 or containing a Pro Tech Toolkit!

    当社のショップを閲覧する
  5. Remove the plastic bottom from the base of the blender. Remove the plastic bottom from the base of the blender.
    • Remove the plastic bottom from the base of the blender.

  6. Holding the center of the fan, grip the knob in the center of the top of the blender with a wrench and twist the wrench counterclockwise. Holding the center of the fan, grip the knob in the center of the top of the blender with a wrench and twist the wrench counterclockwise.
    • Holding the center of the fan, grip the knob in the center of the top of the blender with a wrench and twist the wrench counterclockwise.

  7. Carefully remove the motor and fan from the base of the blender.
    • Carefully remove the motor and fan from the base of the blender.

  8. Now, gently pull the white wire that is connected to the base and the motor. Be careful, as there is a spring behind the contact points, that might try to shoot out and hurt you. Be careful, as there is a spring behind the contact points, that might try to shoot out and hurt you.
    • Now, gently pull the white wire that is connected to the base and the motor.

    • Be careful, as there is a spring behind the contact points, that might try to shoot out and hurt you.

  9. Now, turn the motor over, and remove the black wire from the motor. Again, be warned as the is another spring that wants to shoot out and hurt you here as well. Again, be warned as the is another spring that wants to shoot out and hurt you here as well.
    • Now, turn the motor over, and remove the black wire from the motor.

    • Again, be warned as the is another spring that wants to shoot out and hurt you here as well.

  10. Now de-solder the yellow wire from circuit board. De-solder the wire following these instructions. Be careful, as there is another, black wire, nearby that you do not want to de-solder.
    • Now de-solder the yellow wire from circuit board. De-solder the wire following these instructions.

    • Be careful, as there is another, black wire, nearby that you do not want to de-solder.

まとめ

Now the fan and motor are ready for replacement. To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

Dana

メンバー登録日: 2014年04月14日

665 ポイント

5のガイドは作成済み

チーム

Cal Poly, Team 12-37, Maness Spring 2014 Cal Poly, Team 12-37, Maness Spring 2014人のメンバー

CPSU-MANESS-S14S12G37

4 メンバー

5のガイドは作成済み

コメント1件

My blender would not blend smoothly. It use to make an unusually loud noise when I put the cup and start the motor. I realized the motor had a "play" making me believe it was not tightened enough. I took a look at the pics on this page and then realized it was assembled wrongly. The white rubber used to absorb the movement was placed after the motor was inserted. Thanks to all who have contributed to this Oster page.

Arturo Acosta - 返信

統計データを表示:

過去 24時間: 1

過去 7 日: 8

過去 30 日: 44

今までの合計 4,770