修理を始めるには コミュニティ ストア

Ninja NJ600 Circuit Board Replacement

はじめに

This guide will show how to replace the circuit board in your Ninja Professional Blender, in the event that it stops working. The removal process requires the removal of four screws and the desolder of five components.

必要な工具と部品

  1. Ninja NJ600 Circuit Board Replacement, Blender Base Cover: 手順 1、 2の画像 1 Ninja NJ600 Circuit Board Replacement, Blender Base Cover: 手順 1、 2の画像 2

    • Remove the five screws (13mm long, 6mm head diameter) using a Phillips #2 screwdriver.

    編集

  2. Ninja NJ600 Circuit Board Replacement: 手順 2、 2の画像 1 Ninja NJ600 Circuit Board Replacement: 手順 2、 2の画像 2

    • Without removing any screws, you can pull the 2nd layer free from the base. Do this now and set it down gently next to the base.

    • The power cord runs through a hole in the side of this layer. Squeeze the cord and pull it through the hole to separate the layer from the cord.

    編集

  3. Ninja NJ600 Circuit Board Replacement: 手順 3、 3の画像 1 Ninja NJ600 Circuit Board Replacement: 手順 3、 3の画像 2 Ninja NJ600 Circuit Board Replacement: 手順 3、 3の画像 3

    • Using the Phillips #2 screwdriver, remove these six screws (13mm long, 6mm head diameter). Then carefully remove this layer, and rest it next to the blender base.

    • Be careful not to damage the two wires that are keeping this third layer attached to the base.

    編集

  5. Ninja NJ600 Circuit Board Replacement, Circuit Board: 手順 4、 1の画像 1

    • Remove these four screws (10mm long, 5mm head diameter) using a Phillips #2 screwdriver.

    • Be careful not to scratch the circuit board with the screwdriver.

    編集

  6. Ninja NJ600 Circuit Board Replacement: 手順 5、 1の画像 1

    • Using a pair of scissors or wire cutters, cut the zip tie holding these wires.

    • This will give the circuit board more range of motion.

    編集

  7. Ninja NJ600 Circuit Board Replacement: 手順 6、 3の画像 1 Ninja NJ600 Circuit Board Replacement: 手順 6、 3の画像 2 Ninja NJ600 Circuit Board Replacement: 手順 6、 3の画像 3

    • Desolder the five wires from the solder pads shown.

    • If you do not know how to do this, iFixit has a guide describing the process.

    • Before you begin to desolder these wires, flip the board over to confirm that you are about to desolder the correct component.

    • Soldering iron is very hot, use caution when handling

    編集

  8. Ninja NJ600 Circuit Board Replacement: 手順 7、 1の画像 1

    • After the wires have cooled enough to touch, carefully slide the circuit board free of the wires.

    • NOTE: keep track of which pad each wire was soldered to. This is important for your blender to function.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order, but solder the wires back to the board.

2 の人々がこのガイドを完成させました。

作成者

4人の作成者と共同で作成されました。

Kody D

メンバー登録日: 04/01/15

537 ポイント

3のガイドは作成済み

バッジ: 15

+12 個以上のバッジ

チーム

Cal Poly, Team 24-2, Lancaster Spring 2015 Cal Poly, Team 24-2, Lancaster Spring 2015人のメンバー

CPSU-LANCASTER-S15S24G2

4 メンバー

6のガイドは作成済み

4 件のコメント

Good article. How do I get hold of a board?

Odman - 返信

Where can I buy de circuito board?

carlareis1 - 返信

Where can i buy the circuit board ?

Adesoye Olatunji - 返信

Hi, where can I buy this board please?

Daniel - 返信

コメントを追加

統計データ:

過去 24時間: 1

過去 7 日: 10

過去 30 日: 32

今までの合計 3,407